Spare Parts - Bosch GNA 3,5 PROFESSIONAL Bedienungsanleitung

OBJ_BUCH-101-001.book Page 5 Friday, March 31, 2006 10:33 AM
Changing the Punch
Insert the allen key 4 into the screw head of the punch
adjustment screw 16. Turn the adjustment screw until
it 7 is exact centre of the borehole 8 at the die holder.
Remove the allen key from the punch adjustment screw
16.
Remove the die 14 (refer to "Changing the Die" as well
as the hold down guide 12 and the guide plate 11 (refer
to "Changing the Guide Plate").
Loosen the screw 7 of the punch fastener and pull out
the punch 10 downward. Lubricate the new or the
reground punch properly and insert it from underneath.
Tighten the screw 7 again.
Attach the guide plate 11 and the hold down guide 12
as well as the die 14 (refer to "Changing the Guide
Plate" as well as "Changing the Die").
Regrinding the Punch
In most cases, regrinding the punch in good time (e.g.
with a diamond disc) can usually prevent the punch
from breaking out. Heavily damaged punches may not
be reground.
The punch may not be reground by more than 1 mm.
Grinding may be carried out only alongside the cutting
surface and at exactly 90° to the centre axis.
Set a light edge to the cutting edge of the punch using
a fine whetstone.
WARNING! Important instructions for connecting
a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to the fol-
lowing code:
Do not connect the blue or brown wire to the earth ter-
minal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it must be
disposed of safely.
If the machine should fail despite the care taken in man-
ufacturing and testing procedures, repair should be
carried out by an after-sales service centre for Bosch
power tools.
In all correspondence and spare parts order, please
always include the 10-digit article number given on the
type plate of the machine.

Spare Parts

Punch 10 . . . . . . . . . . . . . . . . . . . . . . . . 3 607 031 357
Die 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 602 380 007
Guide plate 11 . . . . . . . . . . . . . . . . . . . . 3 601 181 039
3 609 929 A61 • 31.3.06
Service and Customer Assistance
Exploded views and information on spare parts can be
found under:
www.bosch-pt.com
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆ Service:. . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 82
✆ Advice line:. . . . . . . . . . . . +44 (0) 18 95 / 83 87 91
Fax: . . . . . . . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 89
Ireland
Beaver Distribution Ltd.
Greenhills Road
Tallaght-Dublin 24
✆ Service:. . . . . . . . . . . . . . . . .+353 (0)1 / 4 14 94 00
Fax: . . . . . . . . . . . . . . . . . . . . . .+353 (0)1 / 4 59 80 30
Australia and New Zealand
Robert Bosch Australia Pty. Ltd.
RBAU/SPT
1555 Centre Road
P.O. Box 66
3168 Clayton/Victoria
✆ . . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 44
Fax: . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 45
www.bosch.com.au
Disposal
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According the European Guideline
2002/96/EC for Waste Electrical and
Electronic Equipment and its implemen-
tation into national right, power tools
that are no longer usable must be collected separately
and disposed of in an environmentally correct manner.
Subject to change without notice.
English–5