General Notes; Safety Instructions - Scheppach Tisa 3.0 Originalanleitung

General notes

• After unpacking, check all parts for any transport dam-
age. Inform the supplier immediately of any faults.
• Later complaints cannot be considered.
• Make sure the delivery is complete.
• Before putting into operation, familiarize yourself with
the machine by carefully reading these in structions.
• Use only original scheppach accessories, wearing or
replacement parts. You can find replacement parts at
your scheppach dealer.
• When ordering, include our item number and the type and
year of construction of the machine.
Dear customer,
We wish you much pleasure and success with your new
scheppach machine.
NOTE:
In accordance with valid product liability laws, the manu-
facturer of this device shall not be responsible for damage
to and from this device which results from:
• Improper care.
• Noncompliance with the Operating Instructions.
• Repairs made by unauthorized persons.
• The installation and use of any parts which are not
original scheppach replacement parts.
• Improper use and application.
• Failure of the electrical system as a result of non-
compliance with the legal and applicable electrical
directives and VDE regulations 0100, DIN 57113 /
VDE 0113.
We recommend that you read through the entire operating in-
structions before putting into operation.
These operating instructions are to assist you in getting
to know your machine and utilize its proper applications.
The operating instructions contain important notes on how
you work with the machine safely, expertly, and economi-
cally, and how you can avoid hazards, save repair costs,
reduce downtime and increase the reliability and service
life of the machine.
In addition to the safety requirements contained in these
operating instructions, you must be careful to observe your
country's applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them from
dirt and humidity. They must be read by every operator
before beginning work and observed conscientiously. Only
persons who have been trained in the use of the machine
and have been informed of the various dangers may work
with the machine. The required minimum age must be ob-
served.
In addition to the safety requirements contained in these
operating instructions and your country's applicable
regulations, you should observe the generally recognized
technical rules concerning the operation of woodworking
machines.
Set-up:
Prepare the workplace where the machine is to be placed.
Insure sufficient room to allow safe work without malfunc-
tions. The machine is designed to operate in closed rooms
and must be placed stabily on firm level ground. Stability
is insured by attachment to the ground with 4 screws (Fig.
18).
Transport:
The machine may only be transported with suitable lifting
devices (crane or fork lift). The connection point for the
rope (crane) is on the upper band wheel cabinet. Never
lift from the saw bench. If the machine is to be moved fre-
quently within the work area, use of the wheel assembly
special accessory is recommended.
In these operating instructions we have marked the places
that have to do with your safety with this sign: m
m Safety instructions
Please pass on safety notes and instructions to all those who
work on the machine.
• The machine must only be used in technically perfect
condition in accordance with its designated use and
the instructions set out in the operating manual, and
only by safety-conscious persons who are fully aware
of the risks involved in operating the machine. Any
functional disorders, especially those affecting the
safety of the machine, should therefore be rectified
immediately.
• Only tools which correspond to the European norm, EN
847-1, may be used.
• Observe all safety instructions and warnings attached
to the machine.
• See to it that safety instructions and wamings attached
to machines are always complete and perfectly legible.
• Caution when working: There is a danger to fingers and
hands from the rotating cutting tool.
• Make sure that the machine stands stable on firm
ground.
• Check all power supply lines. Do not use defective
lines.
• Keep children away from the machine when it is con-
nected to the power supply.
• Operating personal must be at least 18 years of age.
Trainees must be at least 16 years of age, but may only
operate the machine under adult supervision.
• Persons working on the machine may not be diverted
from their work.
• The machine must be equipped with a table length
extension if a second person is work.ing at the circu-
lar sawbench removing cut work.pieces. The second
person may not stand anywhere else but at the take-
off table end.
• The working space on the machine must be free of
chips and wood scrap.
• Wear only close-fitting clothes. Remove rings, bracelets
and other jewelry.
english 9