Ferm PSM1015 Gebrauchsanweisung Seite 3

10
ORBITAL SANDER
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance
of the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
SAFETY INSTRUCTIONS ATTENTION!
When using electric machines always observe the safety
regulations applicable in your country to reduce the risk
of fire, electric shock and personal injury. Read the
following safety instructions and also the enclosed safety
instructions.
Keep these instructions in a safe place!
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use power
tools in damp or wet locations. Keep work area well lit.
Do not use power tools in presence of flammable liquids
or gases.
3. Guard against electric shock.
Prevent body contact with grounded surfaces (e.g. pipes,
radiators, refrigerators).
4. Keep visitors away.
Visitors should be kept away from the work area at all
times. Do not let visitors handle the Electric Rotary
Hammer Drill at any time.
5. Store unused tools.
When not is use keep tools out of reach of children. Store
in a dry and secure location.
6. Do not force tool.
Do not apply undue pressure as this may affect
performance and may cause damage to the machine.
Forcing the job also increases the potential for accidents.
7. Use right tool.
Do not force small tools or attachments to do the job of
heavy duty tool. Do not use a tool for purposes not
intended.
8. Dress properly.
Do not wear loose clothing or Jewellery. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
9. Use safety glasses.
Also use face or dust mask when operation is dusty.
Ferm Ferm
10. Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11. Do not abuse cord.
Never carry tool by cord or yank it to disconnect it from
electrical socket. Keep cord from heat, oil and sharp
edges.
12. Secure work.
Use clamps or a vice to hold work. It's safer than using
your hand and it frees both hands to operate tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically and,
if damaged, have repaired by authorized service facility.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean and free from oil and
grease.
15. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
17. Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch. Be
sure switch is off when plugging in.
18. Outdoor use extension cords.
When tool is used outdoors, use only extension cords
intended for use outdoors and so marked. Always use tool
in conjunction with a residual circuit breaker device.
19. Stay alert.
Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service centre unless otherwise
indicated elsewhere in this instructions manual. Have
defective switches replaced by an authorized centre. Do
not use tool if switch does not turn on and off.
21. Warning.
The use of any other accessory or attachment other than
recommended in this operation instructions or the
catalogue may present a risk of personal injury.
22. Have your tool repaired by an expert.
This appliance is manufactured to very high standards and
meets relevant safety regulations. Repairs should only be
done by a suitable qualified electrical engineer or
otherwise.
23. Hearing protection should be worn.
3