Application; Advice On Application; Procedure For Tens, Ems And Massage Programmes; (Quick Start) - Beurer em 41 Gebrauchsanleitung

i If an electrode becomes detached during the application, the pulse
intensity of both channels goes to the lowest setting. Press the ON/OFF key
to enter pause mode, reposition the electrode and continue application by
pressing the ON/OFF key again and setting the required pulse intensity.

7. Application

7.1 Advice on application

• If the machine is not used within 3 minutes, it switches off automatically
(automatic switch-off function). When it is switched on again, the LCD
main menu screen appears, with the last used submenu flashing.
• If an admissible key is pressed, there is one short beep. If an inadmissible
key is pressed, there are two short beeps.
7.2 Procedure for TENS, EMS and MASSAGE programmes 01–10

(quick start)

• From the programme charts, select a programme that is suitable for your
purpose.
• Place the electrodes in the area selected and connect these
to the machine. The corresponding positioning suggestions
may help you here.
• Press the ON/OFF key in order to switch on the machine.
• Press MENU and navigate through the sub-menus (TENS/
EMS/MASSAGE) and confirm your selection with ENTER.
(Fig. 1, example of TENS display)
• Using the UP/DOWN keys, select the programme you want
and confirm with ENTER (Fig. 2, example of display for No. 1
TENS programme).
• Using the UP/DOWN keys, select the total treatment time
and confirm with ENTER (Fig. 3, example of 30-minute treat-
ment duration).
The machine is in wait status (Fig. 4).
• Press ON/OFF to start the stimulation treatment. The opera-
tion status display starts to change (Fig. 5).
• Select the pulse intensity which is the most comfortable for
you by pressing the key CH 1+/CH 2+.
The pulse intensity display adapts accordingly.
7.3 Procedure for TENS/EMS programmes 11 to 20
(individual programmes)
Programmes 11 to 20 are preset programmes which you can also individualise.
Here you can set pulse frequency.
• From the programme charts, select a programme that is suitable for your
purpose.
• Place the electrodes in the area selected and connect these to the machine.
The corresponding positioning suggestions may help you here.
• Press the ON/OFF key in order to switch on the machine.
• Press MENU and navigate through the sub-menus (TENS/
EMS/MASSAGE) and confirm your selection with ENTER.
(Fig. 1, example of TENS display)
• Using the UP/DOWN keys, select the programme you want
and confirm with ENTER (Fig. 2, example of display for No.
11 TENS programme).
• Using the UP/DOWN keys, select the frequency you want
for Cycle 1 (Hz) and confirm with ENTER (Fig. 3). Repeat
this process for all subsequent cycles.
• To terminate frequency setting, set the frequency (Hz)
after the cycle last required "--0" and press ENTER. All
Fig. 1
frequency settings of subsequent cycles are then automati-
cally set at "0" and thus not taken into account.
i Tip: Hold down the ENTER key for 2 seconds in order to
skip frequency settings and access 'treatment time setting'.
Fig. 2
In the event that you need all 8 cycles, you can also press
ENTER for 2 seconds to terminate selection of frequency
settings.
• Using the UP/DOWN keys, select the desired treatment
Fig. 3
time and confirm with ENTER (Fig. 4, example of 30-minute
treatment duration).
• The machine is in wait status (Fig. 5).
• Press ON/OFF to start the stimulation treatment. The
Fig. 4
operation status display starts to flash (Fig. 6).
• Select the pulse intensity which is the most comfortable for
you by pressing the key CH 1+/CH 2+.
The pulse intensity display adapts accordingly.
Fig. 5
28
Fig. 1 Rys. 1
Fig. 2
Rys. 2
Fig. 3 Rys. 3
Fig. 4 Rys. 4
Fig. 5 Rys. 5
Fig. 6 Rys. 6