Message List - Tascam DR-100MK 3 Bedienungsanleitung

Message list

The following is a list of the pop-up messages.
Refer to this list if one of these pop-up messages appears on the DR-100MKIII
and you want to check the meaning or determine a proper response.
Message Meaning and response
The input level knob and all buttons have been
ALL HOLD on
disabled by the HOLD switch.
The input level knob has been disabled by the
LEVEL HOLD on
HOLD switch.
Battery empty
Recharge the built-in battery or replace the
removable batteries.
Battery low
No card Load an SD card.
Move the write-protection switch to the unlocked
position in order to record or erase data on the SD
Card protected
card.
The SD card was not recognized.
Card error
Change the SD card.
The SD card has no remaining space.
Card full
The SD card is not formatted properly or the card is
broken.
Format error
Press the ENTER/MARK button to start formatting.
Format card
Formatting will erase all the data on the SD card.
Something might be wrong with the SD card.
Invalid card
Change the SD card.
Change card
The SD card is not formatted properly or the card is
broken.
MBR error
Press the ENTER/MARK button to start formatting.
Init card
Formatting will erase all the data on the SD card. If
formatting is not possible, change the SD card.
Writing to the SD card timed out. This has caused
audio to be interrupted and noise to occur.
Write error
REC continue A BOF mark is added at the point when audio was
interrupted.
SD card writing performance has become worse.
A BOF mark has been added at the point when
audio was interrupted because writing to the SD
Card slow
card timed out.
Check BOF MARK
Check the audio around the BOF mark.
Execute the erase format function or change the SD
card.
The system file required to operate this unit is
invalid.
Invalid sys file
Make sys file Press the ENTER/MARK button to create a system
file.
The system file is missing. This unit requires a system
file for operation.
No sys file
Make sys file Press the ENTER/MARK button to create a system
file.
Message Meaning and response
Please see the Reference Manual for file formats
Non-supported
that this unit can use.
Recording is not possible because the total number
File full
of folders and files would exceed the limit of 5000.
A file cannot be found or a file might be damaged.
File not found
Please check that file.
Remove protection from a file before trying to
Can't delete
delete it.
File protected
Can't divide
The file is too short, so it cannot be divided.
File too short
Can't divide
MP3 files cannot be divided.
Current file MP3
The divide function would cause the file name to
be the same as that of an existing file in the same
Can't divide
folder.
Dup file name
Use a computer to change the file name.
Files that do not have marks cannot be divided with
Can't divide
this function.
No mark
Mark division will not work when the interval
Can't divide
between marks is two seconds or less.
Short interval
Can't divide
There is no audio file.
No file
Division is not possible because the file name
Can't divide
would exceed the limit of 200 characters.
File name err
Use a computer to change the file name.
The number of marks has reached the limit of 99.
MARK full
You cannot delete a folder that contains files.
Can't delete
Not empty Delete all the files in the folder and try again.
No XRI data has been saved in the file. Turn the
XRI data recording function ON before starting
No XRI data
recording.
XRI data cannot be saved when recording MP3 files.
Marks cannot be added because the file is
protected from writing.
Can't MARK
File protected Remove protection from a file if you want to add
marks to it.
Can't MARK
Marks cannot be added because the file is too short.
File length
Nothing is connected to the digital input (DIGITAL
IN) connector or the signal is not being input
Digital-In
correctly.
Unlock
Check the digital connection.
Digital-In
Digital input has been properly detected.
Lock
DIN sample The digital input sampling frequency does not
match the recording setting.
Unmatch
The IN and OUT points are too close together. Set
I/O too short
them with at least 1 second between them.
Message Meaning and response
The internal temperature has risen while using the
built-in battery and/or AA batteries.
Thermal Alert
Connect USB PWR Continued use is possible by supplying power with
a USB connection.
The internal temperature has risen.
Thermal Alert
The system will shut down automatically.
If any other error occurs, turn the unit off and restart it.
TASCAM DR-100MKIII
15