Specifications - Makita JR3060T Betriebsanleitung

ENGLISH
1 Shoe
2 Shoe button
3 Lever
4 Stopper
5 Switch trigger

SPECIFICATIONS

Model
Length of stroke ...................................................... 32 mm
Max. cutting capacities
Pipe ............................................................... 130 mm
Wood ............................................................. 255 mm
-1
Strokes per minute (min
Overall length............................................................... 485
Net weight.............................................. 4.2 kg (JR3060T)
......................................................4.4 kg (JR3070CT)
Safety class ................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for sawing wood, plastic, metal and
building materials with a strong impact. It is suitable for
straight and curved cutting.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
SAVE THESE INSTRUCTIONS.
Work area safety
1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
3. Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
Explanation of general view
6 Lock button
7 Adjusting dial
8 Blade clamp lever
9 Released position
10 Fixed position
JR3060T/JR3070CT
) ................................... 0 - 2,800
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and atching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock if
your body is earthed or grounded.
6. Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
7. Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
/II
parts. Damaged or entangled cords increase the risk
of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use educes the risk of elec-
tric shock.
Personal safety
9. Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
10. Use safety equipment. Always wear eye protec-
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
11. Avoid accidental starting. nsure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
12. Remove any adjusting key or wrench before turn-
ing the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
13. Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
14. Dress properly. Do not wear loose clothing or jew-
ellery. Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
15. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
11 Blade
12 Blade clamp lever
13 Limit mark
14 Brush holder cap
15 Screwdriver
5