Ec Declaration Of Conformity - Makita JR3060T Betriebsanleitung

NOTE:
• If you do not insert the saw blade deep enough, the
saw blade may be ejected unexpectedly during opera-
tion. This can be extremely dangerous.
To remove the saw blade, rotate the blade clamp lever in
the direction of the arrow fully. The saw blade is removed
and the blade clamp lever is fixed at the released position
. (Fig. 8)
NOTE:
• If you remove the saw blade without rotating the blade
clamp lever fully, the lever may not be locked in the
released position
clamp lever fully again, then make sure that the blade
clamp lever locked at the released position
OPERATION (FIG. 9)
CAUTION:
• Always press the shoe firmly against the workpiece
during operation. If the shoe is held away from the
workpiece during operation, strong vibration and/or
twisting will be produced, causing the blade to snap
dangerously.
• Always wear gloves to protect your hands from hot fly-
ing chips when cutting metal.
• Be sure to always wear suitable eye protection which
conforms with current national standards.
• Always use a suitable coolant (cutting oil) when cutting
metal. Failure to do so will cause premature blade
wear.
Press the shoe firmly against the workpiece. Do not allow
the tool to bounce. Bring the blade into light contact with
the workpiece. First, make a pilot groove, using a slower
speed. Then use a faster speed to continue cutting.
MAITENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Replacing carbon brushes (Fig. 10 & 11)
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
8
. In this case, rotate the blade
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Recipro saw blade
• Plastic carrying case
EC-DECLARATION OF CONFORMITY
.
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents,
HD400, EN50144, EN55014, EN61000
in accordance with Council Directives, 73/23/EEC, 89/
336/EEC and 98/37/EC.
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
For European countries only
For Model JR3060T
The typical A-weighted noise levels are
The typical weighted root mean square acceleration value
2
is 14 m/s
These values have been obtained according to EN60745.
For Model JR3070T
The typical A-weighted noise levels are
The typical weighted root mean square acceleration value
2
is 9 m/s .
These values have been obtained according to EN60745.
Yasuhiko Kanzaki CE 2005
Director
Noise and Vibration
sound pressure level: 87 dB (A)
sound power level: 98 dB (A)
Uncertainty: 1 dB (A).
- Wear ear protection. -
.
sound pressure level: 88 dB (A)
sound power level: 99 dB (A)
Uncertainty: 0.5 dB (A).
- Wear ear protection. -