Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8
Troubleshooting and Corrective Action
Warning
Make sure that the control air, atomizing air and material input to the spray gun are
shut off prior to any repair work - risk of injury.
Fault
Material noozle is
- Needle seal packing (item 8)
- Needle seat (item 4)
leaky
- O-Ring (item 5)
Insufficient
- Filter clogged
Material Input
- Material noozle too small
- Material Pressure too low
Spray Jet fails to reach
- Material noozle (item 2)
the desired width
worn out
Material leaks
- Needle seal packing
from leakage bore
(item 8)
9
Disposal of Cleaning / Servicing Substances
Disposal of any such substances must be in accordance with all applicable local and
national regulations, directives and laws.
Warning
All processing specifications and safety warnings issued by the manufacturers of
spraying and cleaning media must be observed. The improper disposal of any toxic
waste material represents a serious threat to the environment, i.e. to the health
of mankind and animal life.
10
Specification Data
Net Weight:
Airless Spray Material noozle
Sizes to choice:
Pressure Ranges
max. Control Air Pressure
max. Material Pressure
max. Operating Temperature:
Sound Level
(measured at a distance
of 1 m from the spray gun) :
Right to effect technical changes reserved.
12
Cause
Remedy
• Check
• Clean and / or Replace
• Clean
• Change to larger Size
• Increase Material pressure
• Replace
• Replace
158 g
see Table below
8 bar
120 bar
80° C
82 dB (A)
Noozle
No.
An-
Spray
VolumetricFlowl/min
size
of
gel
pattern
low-
high-
Order
in
viskosity/ viskosity
mm
Materials
163107
10°
50-100
0.189
163207
20°
100-150
0.18
163307
30°
150-200
163407
40°
200-250
163109
10°
50-100
163209
20°
100-150
0.23
163309
30°
150-200
0.303
163409
40°
200-250
163509
50°
250-300
163609
60°
300-350
163111
10°
50-100
163211
20°
100-150
163311
30°
150-200
0.454
0.28
163411
40°
200-250
163511
50°
250-300
163611
60°
300-350
163711
70°
350-400
163113
10°
50-100
163213
20°
100-150
163313
30°
150-200
163413
40°
200-250
0.643
0.33
163513
50°
250-300
163613
60°
300-350
163713
70°
350-400
163813
80°
400-450
163115
10°
50-100
163215
20°
100-150
163315
30°
150-200
0.871
163415
40°
200-250
0.38
163515
50°
250-300
163615
60°
300-350
163715
70°
350-400
163815
80°
400-450
163723
70°
350-400
163823
80°
400-450
2.082
0.58
163923
90°
450-500
163125
10°
50-100
163225
20°
100-150
163325
30°
150-200
163425
40°
200-250
2.498
163525
50°
250-300
0.63
163625
60°
300-350
163725
70°
350-400
163825
80°
400-450
163925
90°
450-500
163127
10°
50-100
163227
20°
100-150
163327
30°
150-200
163427
40°
200-250
2.914
163527
50°
250-300
0.68
163627
60°
300-350
163727
70°
350-400
163827
80°
400-450
163927
90°
450-500
Noozle
No.
An-
Spray
Vol.Flowl/min
size
of
gel
pattern
low-
high-
Order
in
viskos./ viskos.
mm
Materials
163117
10°
50-100
163217
20°
100-150
163317
30°
150-200
163417
40°
200-250
1.136
163517
50°
250-300
0.43
163617
60°
300-350
163717
70°
350-400
163817
80°
400-450
163917
90°
450-500
163119
10°
50-100
163219
20°
100-150
163319
30°
150-200
163419
40°
200-250
1.363
163519
50°
250-300
0.48
163619
60°
300-350
163719
70°
350-400
163819
80°
400-450
163919
90°
450-500
163121
10°
50-100
163221
20°
100-150
163321
30°
150-200
163421
40°
200-250
1.741
163521
50°
250-300
0.53
163621
60°
300-350
163721
70°
350-400
163821
80°
400-450
163921
90°
450-500
163123
10°
50-100
163223
20°
100-150
163323
30°
150-200
2.082
0.58
163423
40°
200-250
163523
50°
250-300
163623
60°
300-350
163129
10°
50-100
163229
20°
100-150
163329
30°
150-200
163429
40°
200-250
3.331
163529
50°
250-300
0.74
163629
60°
300-350
163729
70°
350-400
163829
80°
400-450
0.871
163929
90°
450-500
163131
10°
50-100
163231
20°
100-150
163331
30°
150-200
163431
40°
200-250
3.861
163531
50°
250-300
0.79
163631
60°
300-350
163731
70°
350-400
163831
80°
400-450
1.098
163931
90°
450-500
13
Werbung
Inhaltsverzeichnis
