Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
with the knob CONTROL SELECT and
then press the knob to confirm. To call
up a stored station by means of the
remote control, press one of the buttons
1 – 5; for the storage locations 6 – 10,
first press the button SHIFT and then
one of the buttons 1 – 5.
7) The automatic scan is factory-set to only
stop at stations with strong reception.
For the automatic scan to stop at sta-
tions with poor reception, press the but-
ton MENU. The menu "FM" will appear:
Scan setting
The line
selected. Press the knob CONTROL
SELECT. The following confirmation
prompt will appear:
Turn the knob CONTROL SELECT to
NO
select the setting
knob to confirm.
8) Prior to scanning for the next station,
first wait for the display to indicate the
station most recently set.
Forward scan:
At the unit, press the knob CONTROL
SE LECT.
Note: If the reverse scan starts, briefly turn
the knob to the right in order to change the
scan direction.
On the remote control, keep the but-
ton
pressed until the scan starts.
I
▶ ▶
Reverse scan:
At the unit, briefly turn the knob CON-
TROL SELECT to the left (to change
the scan direction) and then press the
knob.
On the remote control, keep the but-
ton
I
pressed until the scan starts.
◀ ◀
9) Store the station as described in step 5.
Proceed in the same way to scan and
store the other stations.
10) Stations with poor reception may be dis-
turbed by noise. To reduce the noise,
set the reproduction to mono: Press the
button MENU. The menu "FM" will
appear (fig. 37). Select the line
setting
and confirm. The following
confirmation prompt will appear:
20
Turn the knob CONTROL SELECT to
select the setting
the knob to confirm.
Note: All stations will then be reproduced in
mono. For stereo reproduction of stations with
strong reception, set
reception" again.
4.4 Music player
The music player is able to replay audio
files in the formats MP3, AAC, WMA,
WAVE or FLAC from a USB flash drive, a
hard disk or a computer in the local net-
work.
Press the button MODE repeatedly
Music player
until
menu "Music player" will appear:
will be
4.4.1 Replay from the USB port
1) Insert a USB flash drive into the USB
port
port. After a short time, the following
message will appear:
and then press the
YES
tracks stored on the data storage device,
press the knob CONTROL SELECT.
If the message shown in fig. 41 does not
appear, turn the knob CONTROL
SELECT in the menu "Music player" to
select the line
then press the knob to confirm.
2) Once the data storage device has been
opened, its contents will be shown:
Turn the knob CONTROL SELECT to
select a track (if applicable, also from a
folder, indicated by
the knob to start the replay.
Audio
3) To select a different track, turn the knob
CONTROL SELECT. To exit a folder se -
lected, press the button BACK.
4) For information on how to create and
replay a playlist, see chapter 4.4.4.
YES
and then press
NO
in the menu "FM weak
appears. Then, the
or connect a hard disk to the
will be selected. To indicate the
USB playback
>
) and then press
4.4.2 Replay from the computer
The WAP-200 and the computer must be
connected to the same local network. A
UPnP service (Universal Plug and Play),
e. g. Windows Media Player (version 10 or
later), must be installed on the computer.
Windows is a registered trademark of Microsoft Corporation in
the United States and other countries.
1) Switch on the music replay mode so
that the computer can recognise the
WAP-200.
2) Set the computer in such a way that it
works as a media server; for Windows 7,
for example, proceed as follows:
A – Network settings
➞
Start
➞
Control Panel
➞
Network and Internet
➞
Network and Sharing Center
➞
Change advanced sharing settings
(left column)
➞
Click
after "Home or Work".
➞
Under "Media Streaming", click
"Choose media streaming options ...".
➞
If media streaming has not been
turned on yet, an activation window
will appear: Click the button "Turn on
media streaming". (This window will
be skipped when streaming has been
turned on.)
➞
For "Show Devices on", select the
option "All Networks".
➞
After "Media programs on this PC
and remote connections", click "Cus-
tomize ...".
➞
Tick the option "Use default settings"
and click "OK" to confirm.
➞
After "Media programs on this PC and
remote
connections"
tomize", select the setting "Allowed".
➞
Click "OK" to exit the media streaming
and
options.
➞
In the sharing setting options, click
again after "Home or Work".
➞
Under "Network Discovery", select the
setting "Turn on network discovery".
➞
Click "Save All Changes".
➞
Close the window "Network and Shar-
ing Center".
Notes
1. The settings can also be made via the
Windows Media Player (menu "Stream").
2. If applicable, make changes to the Firewall
settings.
B – Setting services
➞
Start
➞
Control Panel
➞
System and Security
➞
Management
➞
Double-click "Services".
➞
Scroll to "SSDP Discovery". The
startup type "Automatic" should have
been selected. If not, click "SSDP Dis-
covery" with the right mouse button,
and, via "Properties", select the
startup type "Automatic". Click "OK"
to confirm.
and
"Cus-
Werbung
Kapitel
Inhaltsverzeichnis
