IMG STAGE LINE 38.7030 Bedienungsanleitung Seite 16

an FM station or manual setting (no
update).
Note: An automatic setting will only be made
when a corresponding station is received.
Therefore, select the setting that corresponds
to the operating mode most frequently used: If
you listen to the digital radio for most of the
time, for example, select
or if you mainly use the Internet to listen to the
radio, leave the setting
unchanged.
Select the setting with the knob CON-
TROL SELECT and then press the knob
to confirm.
5) The following menu displayed depends
on the selected setting; additional time
settings may be required:
Update from DAB
–
No additional time settings are
required (including daylight saving
time change). Continue with step 6.
The menu shown there (fig. 11) will
appear.
Update from Network
–
The menu "Set timezone" will appear:
For Great Britain, the correct setting
has been selected:
UTC +00:00:Dublin, London
Press the knob CONTROL SELECT
to confirm this setting or, for a differ-
ent country, first select the appropri-
ate time zone and then confirm your
selection. The menu "Daylight sav-
ings" will appear:
During the winter time, leave the set-
OFF
ting unchanged; for the summer
time, select the setting
knob CONTROL SELECT. Press the
knob to confirm the setting. Continue
with step 6. The menu shown there
(fig. 11) will appear.
no Update
–
The menu for the manual time setting
will appear:
The digits for the day will flash. Turn
the knob CONTROL SELECT to set
the day and then press the knob to
confirm. The digits for the month will
start flashing. Proceed in the same
way to set the month, the year, the
hours, the minutes and, if required,
16
AM or PM. To return to the previous
setting, press the button BACK.
6) When the final time setting has been
confirmed, the following message will
briefly appear:
Update from DAB ,
Update from NET
Then a country list for the network set-
ting will appear:
FM
or
7) The
selected. For Great Britain, press the
knob CONTROL SELECT to confirm
this setting. The unit will search for a
network:
⑧
Then the menu with the networks found
will appear:
A To establish the connection to the
network later (otherwise continue
with item B, C or D):
Press the button MENU; answer
the question
⑨
at
The WAP-200 can now be used
(chapter 4), however, not as an Inter-
ON
with the
net radio.
B If the name of your router is shown in
this menu:
Turn the knob CONTROL SELECT to
select the name and then press the
knob to confirm. If the network access
is not encoded, the connection to the
network will be established; continue
with step 10. If the access is encoded,
continue with step 8.
C If the name is not shown and if the
WAP-200 is connected to the router
via a cable:
⑩
Use the knob CONTROL SELECT to
select the line
press the knob to confirm. If the net-
work access is not encoded, the con-
nection to the network will be estab-
lished; continue with step 10. If the
access is encoded, continue with
step 8.
⑪
⑫
line Most of Europe
⑬
⑭
Run wizard again
next start up? with
[Wired]
and then
D If the name is not shown and if a wire-
less connection shall be made to the
router:
a) Use the knob CONTROL SELECT
to select the line
[Manual config]
and then press the knob to con-
firm.
b) In the following menu, select
Wireless
c) In the following menu, select the
DHCP enable
line
the router automatically transfers
the network settings to the WAP-
200 via DHCP (Dynamic Host
Configuration Protocol).
If the DHCP function at the router
is deactivated or not available, se-
lect the line
confirm and make the network set-
tings manually in the following
is
submenus; then continue with
step d.
d) The menu for entering the network
name will appear:
Turn the knob CONTROL SE -
LECT to select the first character
and then press the knob to con-
firm. Proceed in the same way to
enter the other characters. Then
select the field
between the special characters
and the digits) and press the knob.
BKSP
= delete last character
CANCEL
= return to the previous
menu
e) The menu "Authentication" will
appear:
NO .
In most cases, the setting
(Wi-Fi Protected Access 2) must
be selected for newer routers.
f) The menu "Encryption type" will
appear:
For most routers, the setting
(Temporal Key Integrity Protocol)
must be selected.
and confirm.
and confirm if
DHCP disable
,
⑮
OK
(to be found
⑯
WPA2
⑰
TKIP