Making Manual Settings; Selecting The Menu Language; Removing Registered Networks; Resetting The Unit To Its Factory Settings - IMG STAGE LINE 38.7030 Bedienungsanleitung

8) If the network access is encoded, a
menu for entering the password will
appear (for a WPS-encoded network,
continue with step 9).
Turn the knob CONTROL SELECT to
select the first character and then press
the knob to confirm. Proceed in the
same way to enter the other characters.
BKSP OK
The three fields ,
have the following functions:
BKSP
– (Backspace) delete last
character
OK
– password is complete, estab-
lish the network connection
CANCEL
– return to the previous menu
The position for selection is between the
special characters and the digits. Press
the knob CONTROL SELECT to exe-
cute the function.
9) If the network access is WPS-encoded
(Wi-Fi Protected Setup), the WPS menu
will appear:
The easiest way to establish the con-
nection is to use the function "Push but-
ton". The corresponding menu line has
already been selected. Press the knob
CONTROL SELECT: The menu "WPS
Setup" will appear. The WPS-200 will
ask you to press the WPS button at the
router. The connection will then be
established. Finally, press the knob
CONTROL SELECT at the WAP-200.
10) After the final entry required with regard
to the network has been made, the con-
nection will be established. This will be
indicated by various messages
Please wait ...
Once the network connection has been
established, the message
will appear, followed by the message
Press the knob CONTROL SELECT to
exit the setup wizard – the main menu
will appear. Use the main menu or the
button MODE to select the operating
mode desired (chapter 4).
Note: If the wizard fails to establish a connection
to the router (message failed to connect
first reset the unit to its factory settings (chap-
ter 3.6) and then make the settings manually.

3.4 Making manual settings

All settings can also be made manually
without the setup wizard:
1) Press the button MENU. Independently
from the menu called up or from the cur-
rent operating mode, a menu containing
the line
appear.
2) Turn the knob CONTROL SELECT to
⑱
select the line
and then press the knob to confirm. The
menu "System settings" will appear:
CANCEL
and
This menu can be used to make all
settings. Turn the knob CONTROL
SELECT to select a setting and then
press the knob to confirm.
3) To return to the previous menu, press
the button BACK.
An overview of the menu structure can be
found on page 23.

3.4.1 Selecting the menu language

Instead of English, a different menu lan-
guage can be selected:
1) In the menu "System settings" (fig. 21),
select the line
CONTROL SELECT and then press the
⑲
knob to call up the menu "Language":
2) Select the desired language in this
menu. Once the selection has been con-
firmed, the menu "System settings" will
appear in the language selected.
3) Press the button MODE (repeatedly)
to select the operating mode desired
(chapter 4).

3.5 Removing registered networks

Connected
The WAP-200 will remember the four wire-
less networks to which it was most recently
connected. When switched on, it will try to
find one of these networks and will connect
to the network found. To call up the list of
registered networks:
1) Press the button MENU.
⑳
2) Select the following:
➞ System settings
werk profile
3) Remove the networks that are not cur-
rent anymore from the list. Turn the knob
CONTROL SELECT to select the net-
works one after the other and press the
),
knob to remove them. Thus, wrong con-
nections can be avoided.
System settings
will
System settings
Language
with the knob
➞ Network ➞ Net-
3.6 Resetting the unit to its factory
settings
Resetting the unit to its factory settings will
also remove all stations stored, disconnect
the connection to the Internet, delete the
connection data and set the menu lan-
guage to English.
1) Press the button MENU.
2) Select the following:
➞ ➞
System settings Factory reset
Proceed?
3) In the following menu
YES
firm the reset with .
, con-
17