Kenwood KDC-320UI Bedlenungsanleitung Seite 22

AUDIO SETTINGS
LOUDNESS LEVEL1/LEVEL2 or LV1/LV2: Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level. ; OFF: Cancels.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
FADER (Not applicable if 3-way crossover is selected.)
R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source. (Before adjustment, select the
source you want to adjust.)
SOUND EFFECT
SOUND RECNSTR (Not applicable for RADIO source and AUX source.)
(Sound ON: Creates realistic sound by compensating the high-frequency components and restoring
reconstruction) the rise-time of the waveform that are lost in audio data compression. ; OFF: Cancels.
SPACE ENHANCE (Not applicable for RADIO source.)
SMALL/MEDIUM/LARGE or SML/MED/LRG: Virtually enhances the sound space. ;
OFF: Cancels.
SND REALIZER LEVEL1/LEVEL2/LEVEL3 or LV1/LV2/LV3: Virtually makes the sound more realistic. ;
OFF: Cancels.
STAGE EQ LOW/MIDDLE/HIGH or LOW/MID/HI: Virtually adjust the sound position heard from the
speakers. ; OFF: Cancels.
DRIVE EQ ON: Boosts the frequency to reduce the noise heard from outside the car or running noise
of the tyres. ; OFF: Cancels.
Depending on the crossover type you have selected ( 5), 2-way crossover or 3-way
SPEAKER SIZE
crossover setting items will be shown. ( 19)
X'OVER
By default, 2-way crossover type is selected.
DTA SETTINGS
For settings, 20, Digital Time Alignment settings.
CAR SETTINGS
• : For 2-way crossover: [SUB-W LEVEL]/[SUBWOOFER SET] is selectable only if
[SWITCH PREOUT] is set to [SUB-W]. ( 4)
• [SUB-W LEVEL] is selectable only if [SUBWOOFER SET] is set to [ON].
18
ENGLISH
Crossover settings
Below are the available setting items for 2-way crossover
and 3-way crossover.
SPEAKER SIZE
Selects according to the connected speaker size for
optimum performance.
• The frequency and slope settings are automatically set
for the crossover of the selected speaker.
• When 2-way crossover is selected, if [NONE] is selected
for [TWEETER] of [FRONT], [REAR] and [SUBWOOFER] for
[SPEAKER SIZE], the [X ' OVER] setting of the speaker is not
available.
• When 3-way crossover is selected, if [NONE] is selected
for [WOOFER] of [SPEAKER SIZE], the [X ' OVER] setting of
[WOOFER] is not available.
X ' OVER
• [FRQ]/[F - HPF FRQ]/[R - HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/
[LPF FRQ]: Adjusts the crossover frequency for the
selected speakers (high pass filter or low pass filter).
If [THROUGH] is selected, all signals are sent to the
selected speakers.
• [F - HPF SLOPE]/[R - HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]/
[LPF SLOPE]/[SLOPE]: Adjusts the crossover slope.
Selectable only if a setting other than [THROUGH] is
selected for the crossover frequency.
• [SW LPF PHASE]/[PHASE]: Selects the phase of the speaker
output to be in line with the other speaker output.
• [GAIN LEFT]/[GAIN RIGHT]/[F - HPF GAIN]/[R - HPF GAIN]/
[SW LPF GAIN]/[GAIN]: Adjusts the output volume of the
selected speaker.