Herunterladen Diese Seite drucken

Scheppach HC65 Originalbetriebsanleitung Seite 25

Vorschau anzeigen Andere Handbücher für HC65:
Verfügbare Sprachen

Verfügbare Sprachen

  • DEUTSCH, seite 1
- Unused power tools should be stored in a dry, ele-
vated or closed location out of the reach of children.
6.
Do not overload your power tool
- They work better and more safely in the specified
output range.
7.
Wear suitable clothing
- Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
- Rubber gloves and anti-slip footwear are recom-
mended when working outdoors.
- Tie long hair back in a hair net.
8.
Do not use the cable for purposes for which it is
not intended
- Do not use the cable to pull the plug out of the outlet.
Protect the cable from heat, oil and sharp edges.
9.
Take care of your tools
- Keep your compressor clean in order to work well
and safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
- Check extension cables regularly and replace
them when damaged.
10. Pull the connector out of the socket
- When the power tool is not in use or prior to main-
tenance and when replacing tools such as saw
blades, drill bits, cutters.
11. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
12. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
- Only use cable reels in the unrolled state.
13. Always remain attentive
- Pay attention to what you are doing. Remain sen-
sible when working. Do not use the power tool
when you are distracted.
14. Check the power tool for potential damage
- Protective devices or other parts with minor dam-
age must be carefully inspected to ensure that
they function correctly and as intended prior to
continued use of the power tool.
- Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the power tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
specialist workshop, insofar as nothing different
is specified in the operating manual.
- Damaged switches must be replaced at a cus-
tomer service workshop.
- Do not use any faulty or damaged connection
cables.
- Do not use any power tool on which the switch
cannot be switched on and off.
15. Have your power tool repaired by a qualified elec-
trician
- This power tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
16. Attention!
- For your own safety, only use accessories and
additional equipment that are indicated in the
operating manual or have been recommended or
indicated by the manufacturer. Use of other tool
attachments or accessories that those recom-
mended in the operating manual or in the cata-
logue could represent a personal danger to you.
17. Noise
- Wear hearing protection when using the com-
pressor.
18. Replacing the connection line
- If the connection line is damaged, it must be re-
placed by the manufacturer or an electrician to
avoid danger. Danger due to electrical shocks!
19. Inflating tyres
- Check the tyre pressure immediately after filling us-
ing a suitable pressure gauge, e.g. at a petrol station.
20. Street-legal compressors in construction site op-
eration
- Ensure that all hoses and fixtures are suitable for
the maximum permissible working pressure of the
compressor.
21. Set-up location
- Only set up the compressor on a flat surface.
22. It is recommended to equip the feed hoses with a
safety cable in case of pressure above 7 bar, e.g.
using a wire cable.
23. Avoid over-stressing the piping system by using
flexible hose connections to prevent kinking.
24. Make sure that the oil cooling devices are kept
clean and that the protective devices are kept in
good operating condition.
25. Risk of burns from hot oil
- Wear suitable protective gloves.
- Never work with the compressor near naked
flames.
www.scheppach.com
GB | 25
loading