Scheppach HL570LS Originalbetriebsanleitung Seite 34

the transport wheel (12). If necessary, use nee-
dle-nose pliers*.
10. Repeat the process with the other transport wheel
(12).
11. Now connect the two front and rear legs (14/7)
to the mountings on the main unit and secure the
connections with the Allen screws M8x55 mm,
washers and nuts M8 (D). Use an Allen key AF 6*
and an open-ended spanner AF 13*.
10.2 Fitting the handlebar (4) (Fig. 11)
1. Fasten the handle (4) to the U-bow (10) with two Al-
len screws M6x16 mm (E). Use an Allen key AF 5*.
10.3 Installation of tray table 1 (17) (Fig. 12)
1. Stand behind the product.
2. Align the right-hand outer mounting hole of the tray
table 1 (17) with the mounting hole on the cylinder
cover (5) and fit the Allen screw M6x12 mm with
the spring washer (F). Use an Allen key AF 5*.
3. Secure the left mounting hole of the tray table 1 (17)
to the connecting plate of the tube rail using an Al-
len screw M6x12 and a locknut M6 (F). Use an Allen
key AF 5* and an open-ended spanner AF 10*.
4. Loosen the Allen screw M8x50 mm (L) without re-
moving it. Use an Allen key 6 mm* for this.
5. Place the support bracket 1 (19) with the open side
between the washer and the frame tube.
6. Align the mounting holes of the tray table 1 (17)
and the support bracket 1 (19) and install the Phil-
lips screw with the locknut M6 (F). Use a Phillips
screwdriver* and an open-ended spanner AF 10*.
7. Tighten the Allen screw M8x50 mm (L) again using
the Allen key AF 6*.
10.4 Installation of tray table 2 (18) (Fig. 13)
1. Stand behind the product.
2. Align the mounting holes of the tray table 2 (18) as
shown in the illustration.
3. Mount the left side of the tray table 2 (18) to the cyl-
inder (5) using the Allen screw M6x12 mm and the
spring washer (G). Use an Allen key 5 mm* for this.
4. Secure the right mounting hole of the tray table 2
(18) to the connecting plate of the tube rail using
an Allen screw M6x12 and a locknut M6 (G). Use
an Allen key AF 5* and an open-ended spanner
AF 10*.
5. Loosen the Allen screw M8x55 mm (D) on the
mounting of the rear leg (7) without removing it.
Use the enclosed Allen key AF 6 and an open-end-
ed spanner AF 13*.
34 | GB
6. Place the support bracket 2 (20) with the open side
between the washer and the frame tube.
7. Align the mounting holes of the tray table 2 (18)
and the support bracket 2 (20) and install the Phil-
lips screw with the locknut M6 (G). Use a Phillips
screwdriver* and an open-ended spanner AF 10*.
8. Tighten the Allen screw M8x55 mm (D) again us-
ing the Allen key AF 6* and the open-ended span-
ner AF 13*.
10.5 Installation of tray table 3 (3) (Fig. 14 - 16)
1. Stand in front of the operating side of the product.
2. Align the mounting holes of the tray table 3 (3) as
shown in the illustration.
3. Mount the right side of the tray table 3 (3) to the cyl-
inder (5) using the Allen screw M6x12 mm and the
spring washer (H). Use an Allen key 5 mm* for this.
4. Secure the left mounting hole of the tray table 3 (3)
to the connecting plate of the tube rail using an Al-
len screw M6x12 and a locknut M6 (H). Use an Al-
len key AF 5* and an open-ended spanner AF 10*.
5. Loosen the Allen screw M8x55 mm (D) on the
mounting of the rear leg (7) without remov-
ing it. Use the enclosed Allen key AF 6* and an
open-ended spanner AF 13*.
6. Place the support bracket 3 (21) with the open side
between the washer and the frame tube.
7. Align the mounting holes of the tray table 3 (3)
and the support bracket 3 (21) and install the Phil-
lips screw with the locknut M6 (H). Use a Phillips
screwdriver* and an open-ended spanner AF 10*.
8. Tighten the Allen screw M8x55 mm (D) again us-
ing the Allen key AF 6* and the open-ended span-
ner AF 13*.
9. Connect tray table 2 (18) and set-down table 3 (3)
with two Phillips screws M6 and the lock nuts M6
(I). Use a Phillips screwdriver* and an open-ended
spanner AF 10*.
10.6 Fitting the protective cage (Fig. 17/18)
1. Connect the rear protective grids (24/27) to each
other and secure them with two Phillips screws
M6x20 mm, clamping clips and nuts M6 (J). Use a
Phillips screwdriver* and an open-ended spanner
AF 10* for this.
2. Attach the guards (24/27) to the holes provided on
the side of tray table 1 (17) and tray table 2 (18).
Use the Phillips screws M6x20 mm, the clamp-
ing clips and the nuts M6 (J) as well as a Phillips
screwdriver* and an open-ended spanner AF 10*
for this.
www.scheppach.com