MPM MOD-56 Bedienungsanleitung Seite 15

EN
APPLIANCE ASSEMBLY
1. Press both latches on the suction hose mounting ring (17), insert the ring into the opening (7)
and release the latches. To disassemble, press the latches again and remove the ring (17) from
the opening (7).
2. Connect the other side of the suction hose (18) to the handle (19) and connect the metal tel-
escopic wand (16) to the other side of the handle (19). Install one of the tools, (20), (21) or (22),
on the end of the wand.
USING THE APPLIANCE
1. Before turning on the vacuum cleaner, unwind the power cord (9) to a suitable length and plug
it into the mains socket. The yellow mark on the power cord indicates the optimum length. Do
not pull out the cord beyond the red mark! While unwinding the cord, do not press the cord
winder button (24).
2. Press the switch (1) to turn on the vacuum cleaner. When at work, you can regulate the suction
power by moving the suction power control left or right to a suitable position.
NOTE! It is recommended to set the suction power control (1) to MIN before turning on
the vacuum cleaner!
WARNING! Dust bag filling level indicator light turns red when the suction hose is
clogged or the dust bag is full. You need to replace the dust bag or remove the clogging
from the suction hose.
3. To wind the power cord, press the cord winder button (24) with one hand, while holding the
cord with another hand to prevent a sudden movement that could damage it.
4. To ensure optimum appliance setting upon the completion of work, use the guide (3) in the rear
of the vacuum cleaner. Place the rail in the rear of the floor-carpet attachment with connected
suction hose and telescopic pipe on the guide. The second guide that facilitates vacuum clean-
er storage in the vertical position is under the bottom of the appliance.
ACCESSORIES OVERVIEW
FLOOR-CARPET ATTACHMENT
Designed for cleaning large flat surfaces. It is equipped with castors that facilitate move-
ment in difficult to access places and a flexible joint, connecting it with the suction hose,
which allows directing at various angles. When you press the button on the upper attach-
ment housing (switch it to the brush mode), a row of rigid bristles will appear on the bottom
to facilitate cleaning hard floors.
SLIT ATTACHMENT WITH MOVABLE BRUSH
Used for cleaning difficult to access areas, such as in room corners, by and below pieces of
furniture and in bends and slits. It is also perfect for cleaning computer keyboards, draw-
ers, radiators or window frames.
REPLACING THE DUST BAG
To replace the dust bag, disconnect the appliance from the power supply, detach the suc-
tion hose (18), press the button (6) to open the upper cover (5), slide out the dust bag, while
holding the flange with the inlet opening directed upwards. Install new dust bag. You can
purchase spare dust bags.
26
AIR FILTER CLEANING AND REPLACEMENT
Normal use of the vacuum cleaner requires periodical replacement or cleaning of the air
filter, which protects the motor from the side of the dust bag, and the air outlet filter. For
this purpose, disconnect the appliance from the power supply and detach the suction
pipe.
1. Release the latch in the cover (10), remove the cover and then remove the filters (11), (12), (13).
2. Remove the motor filter (23). You will access the filter by lifting the cover (5) and removing the
dust bag (14). Remove the filter element (23).
3. Clean the HEPA filter element (12) of dust. The HEPA filter element must be perfectly dry be-
fore installing it again. Before closing the cover (10), make sure that the HEPA filter element is
aligned. Do not wash the HEPA filter element.
4. Wash filter cartridges (11), (13), (23) under running and cool water. Dry the filters thoroughly
after washing.
5. Cartridges should be cleaned every month or more frequently (depending on the usage). If a
cartridge is too contaminated or damaged, replace it with a new one.
6. When installing the filter elements, carefully align them in the housing and the vacuum cleaner.
CAUTION! The filter cartridge being mounted must be completely dry. Mounting a wet
filter may cause an electric shock.
CLEANING AND MAINTENANCE
1. Periodically clean the vacuum cleaner housing and other external elements with a damp cloth.
This will allow maintaining good appearance of the appliance.
2. For this purpose, do not use sharp objects or any strong detergents (e.g. solvents), as this will
cause permanent damage to the vacuum cleaner housing.
3. For air filters and dust bag, follow the above instructions.
IN CASE OF FAILURE
Failure type: Possible causes:
front cover not thoroughly dust bag not attached or
closed attached improperly
a slight housing temperature increase is normal, but if the
vacuum cleaner housing
temperature increases considerably, immediately turn off the
overheating
vacuum cleaner and contact the service
strongly contaminated filters
full dust bag
low suction power
blocked hose or extension pipe
EN
Instructions:
attach the dust bag properly
clean or replace the filters
replace the dust bag or empty
the textile bag
remove all items blocking the
hose or pipe
27