Technical Data; Before Starting The Machine; Operation - EINHELL BG-PH 2652 Originalbetriebsanleitung

Anleitung_BG-PH_2652_SPK1__ 12.06.12 08:20 Seite 14
GB

4. Technical data

Engine type:
2-stroke engine, air-cooled, chrome cylinder
Engine output (max.):
Displacement:
Idle speed of engine:
Max. engine speed
Weight (with empty tank):
Cutter rail length:
Cutting length:
Tooth spacing:
Cutting capacity (max.)
Tank capacity:
Spark plug:
Max. cutting speed
Vibration (front handle) a
hv
K uncertainty
Vibration (rear handle) a
hv
K uncertainty
Sound pressure level L
pA
K uncertainty
Sound power level L
WA
K uncertainty
Sound and vibration were measured in accordance
with DIN EN 10517.

5. Before starting the machine

5.1 Installation
The hedge trimmer is supplied fully assembled. No
assembly work is required.
To make it easier to control, the machine is fitted with
a rotary handle that can be adjusted as required into
positions at angles of -90°/-45°/0°/+45°/+90°. To do
this, pull the lever (Fig. 5/Item B) backwards, turn the
rotary handle into the required position and then
allow the lever to lock at the front again. The various
adjustable positions facilitate working above head
height or in other places with different access.
Please note: The rotary handle may only be
adjusted when the engine is switched off.
14
5.2 Fuel and oil
Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
0.75 kW / 1.0 hp
Please note: Do not use a fuel mixture which has
26 ccm
been kept for longer than 90 days.
2960 min -1
Please note: Do not use 2-stroke oil with a
8800 min -1
recommended mixing ration of 100:1. If inadequate
5.5 kg
lubrication causes engine damage, the
manufacturerʼs engine warranty will be voided.
65 cm
Please note: Only use containers designed and
52 cm
approved for the purpose to transport and store fuel.
28 mm
Pour the correct quantities of petrol and 2-stroke oil
19 mm
into the mixing bottle (see scale printed on the
0.5 l
bottle). Then shake the bottle well.
NGK BPMR7A
5.3 Fuel mixture table
2300 ± 100 cuts/min
Mixing procedure: 40 parts petrol to 1 part oil
13.33 m/s 2
1,5 m/s 2
1 liters
7.69 m/s 2
5 liters
1,5 m/s 2
97 dB
3 dB

6. Operation

107 dB
Please note that the statutory regulations governing
3 dB
noise abatement may differ from town to town.
6.1 Starting the engine from cold (Fig. 3-5)
Fill the tank with the required amount of oil/petrol
mix.
1. Set the machine down on a hard, level surface.
2. Set the choke lever (Fig. 4/Item 5) to " ".
3. Press the fuel pump (primer) (Fig. 4/Item 9) 10
times.
4. Move the ON/OFF switch (Fig. 3/Item 6) to "I"
5. Secure the throttle lever. To do this, press the
throttle lever lock (Fig. 3/Item 13) and then press
the throttle lever (Fig. 3/Item 14) and lock the
throttle lever by pressing the locking knob (Fig.
3/Item 7) at the same time.
6. Hold the machine by the front handle in your
right hand and pull the starter cable (Fig. 5/Item
A) up to the first resistance point (approx. 10
cm). Then tug sharply on the starter cable 4
times. The machine should start.
Please note: Never allow the starter cable to
snap back. This may damage the machine.
7. If the engine has started, set the choke lever
immediately to "
Petrol 2-stroke oil
25 ml
125 ml
" and allow the machine to