Installation - Bestway SPLASH FRAME POOL Bedienungsanleitung

Preparation
NOTE: The pool must be set up on a completely flat and level surface. Please do not install the pool if the surface is inclined or slope.
• Check with your local city council for by-laws relating to fencing, barriers, lighting and safety requirements and ensure you comply with all laws.
• Take the pool and accessories out of the carton with care. If the pool set comes with a ladder, the ladder requires a crosshead screwdriver or an
adjustable wrench ( not included ) to assemble.
• Locate your pool with a minimum of 122cm (48 inch) space on all sides so that a child can not use an object to climb into the pool. Do not set up
directly under overhead power lines or trees and be sure the location does not contain underground utility pipes, lines or cables of any kind.
• It is essential the pool is set up on solid, level ground. If the pool is set up on uneven ground it can result in collapse of the pool and flooding, causing
serious personal injury and/or damage to personal property. Setting up on uneven ground will void the warranty and service claims.
• Sand should not be used to create a level base, the ground should be dug out if necessary.
• Do not set pool up on driveways, decks, platforms, gravel or asphalt. Ground should be firm enough to withstand the pressure of the water; mud,
sand, soft / loose soil or tar are not suitable.
• The ground must be cleared of all objects and debris including stones and twigs.
NOTE: lawn or other vegetation under the pool will die and may cause odors and slime, therefore we recommend removing all grass from where the
pool will be located. Avoid locating your pool over or beside areas prone to aggressive plant and weed species as they may grow through the ground
cloth or liner.
• We highly recommend that once the pool is unfolded on the ground cloth to let it sit exposed to direct sunlight for 1 hour or more so that the pool is
more flexible during set up.
• If purchased with a pump, the pump should be installed after pool is fully assembled. Remember to locate the intake and return outlets towards the
outside power source.
NOTE: If you bought a filter pump, this element has a separate manual instructions. Please open its relative box for details.
• If you bought a separate ladder for your pool, make sure it matches the pool size.
• Regularly check to make sure the ladder is properly assembled.
NOTE: The ladder is only to be used for entering and exiting the pool.

Installation

Fig. 1
Fig. 5
J
K
F
Assembly of the Steel Pro Frame pool can be completed without tools.
NOTE: It is important to assemble pool in the order shown below. Install your pools according to the above illustrations.
1. Lay out all parts and check that you have the correct quantities as listed in the parts guide. If you are missing any parts do not assemble the pool
contact our Customer Service Department for assistance.
2. If pool was purchased with a ground cloth, spread it out at the desired location. Ensure the pool is located within distance of a 220-240volt AC outlet
protected by a RCD (Residual Current Device).
3. Place the Leg Bands (L) on the ground (See Fig. 1). There are different lengths of Leg bands (L), please ensure you have used the correct sizes at the
correct locations.
4. Spread out the pool and put it on the Leg Bands (L). Make sure it is right side up (See Fig. 2). Let it sit exposed to direct sunlight for 1 hour or more so
the pool is more flexible during set up.
5. Ensure the drain valve is located near the area where your plan to drain the water and pump valves are facing the RCD outlet.
ATTENTION: Do not drag the pool on the ground in order to avoid damaging the linear on sharp objects. Bestway Inflatables will not be responsible for
damage caused to the pool due to mishandling or failure to follow these instructions.
6. Insert all of the top rails into the pole sleeves on the top of the pool (See Fig. 3). The combinations for top rails are different for different sizes pools,
see the Structure Section for detail.
7. At the middle opening of each sleeve, insert the two ends of the top rails into the Connector (I). (See Fig. 4)
NOTE: At each Connector ensure both top rails are properly inserted.
8. At the corners, insert the top rails into the Corner Seats (J). Insert the Connection Pins (K) into the pre-drilled holes locking the top rails into position.
(See Fig. 5)
9. Insert the Vertical Pool Legs (F) into the bottom of the Corner Seats (J). (See Fig. 5)
10. On the sides of the rectangle, insert the Vertical Pool Legs (F) or the Y-Vertical Pool Legs (G) into the vertical holes of the Connectors (I). (See Fig. 6)
11. Connect the Side Support Legs (H) to the Y-Vertical Pool Legs (G). Ensure the spring-loaded pins lock into the pre-drilled holes. (See Fig. 6)
12. On each corresponding Pool Leg located on the sides of the rectangle, put the Pool Legs (F or G) through the loops of the Leg Bands (L). This will
keep both corresponding pool legs locked in position. (See Fig. 6)
13. Attach all Footings (M&N) to the bottom of the Vertical Pool Legs (F) and the Side Support Legs (H). (See Fig. 7)
NOTE: Make sure all the Footings (M) under the Y-Vertical Pool Legs (G) are on the floor, an unequal force will make the Side Support Legs (H)
irreparable damage. Failure setting up will void the warranty and service claims.
14. Test the Frame to ensure all connections are secure before filling with water.
15. Insert the blue stopper plug into the inlet and outlet on the inside wall of the pool.
16. Ensure drain valve is firmly closed.
17. Put 1'' to 2'' water in the pool to cover the floor. Once pool floor is slightly covered, gently smooth out all wrinkles. Start in the center of the pool and
work your way clockwise to the outside.
Fig. 2
F/G
Fig . 6
L
H
G
Fig. 3
Fig . 7
6
Fig. 4
I
Bestway
®
S-S-000781