Appliance Safety; Electrical Safety; Vibration Load; Noise Pollution - Al-Ko Multitool Mt 40 Betriebsanleitung

GB
4.5

Appliance safety

■
Only use the appliance under the following
conditions:
■
The appliance is not soiled.
■
The appliance show no signs of damage.
■
All controls function properly.
■
Keep all appliance handles dry and clean.
■
Do not force the power tool. It is intended for
light work in the private sector. Overload can
lead to damage to the appliance.
■
Never operate the appliance with worn or de-
fective parts. Always replace defective parts
with original spare parts from the manufactur-
er. If the appliance is operated with worn or
defective parts, guarantee claims against the
manufacturer are excluded.
4.6

Electrical safety

■
To avoid short-circuits and destroying electri-
cal components:
■
Protect the appliance against humidity
and do not use it in the rain.
■
Do not spray the appliance with water.
■
Do not open the appliance.
NOTE Heed the safety instructions for the
rechargeable battery and for the charging unit in
the separate operating instructions.
4.7

Vibration load

■
Danger due to vibration
The actual magnitude of the vibration emis-
sions during the use of the appliance may de-
viate from that stated by the manufacturer.
Observe the following influencing factors be-
fore or during use:
■
Is the appliance being used as intended?
■
Is the material being cut or processed in
the proper manner?
■
Is the appliance in a proper condition of
use?
■
Is the cutting tool properly sharpened or
is the correct cutting tool installed?
■
Are the handle grips and any optional vi-
bration grips mounted, and are they firm-
ly attached to the appliance?
■
Only operate the tool at the motor speed re-
quired for the respective work. Avoid using
the maximum speed in order to reduce noise
and vibrations.
■
The noise and vibrations of the tool may in-
crease due to improper use and mainte-
24
Safety instructions relating to operation
nance. This leads to health damage. In this
case, immediately switch off the tool and
have it repaired by an authorised service
workshop.
■
The degree of stress due to vibration de-
pends on the work to be performed or on the
use of the tool. Estimate the stress and plan
appropriate work breaks. This considerably
reduces stress due to vibration over the en-
tire working time.
■
Extensive use of the tool exposes the opera-
tor to vibrations, which can lead to circulatory
issues ("white fingers"). To avoid this risk,
wear gloves and keep your hands warm. If
any symptoms of "white fingers" occur, im-
mediately consult a physician. These symp-
toms include: Numbness, loss of feeling, tin-
gling, itching, pain, reduced muscular
strength, changes in the colour or condition
of the skin. Normally these conditions affect
the fingers, hands or pulse. The risk increas-
es at low temperatures.
■
Take long breaks during your working day so
you can recover from the noise and the vibra-
tions. Plan your work in such a way that the
use of appliances that generate strong vibra-
tions is spread over several days.
■
If you notice an unpleasant sensation or disc-
olouration of the skin on your hands when us-
ing the tool, stop work immediately. Take suf-
ficient work breaks. Without sufficient breaks,
a hand/arm vibration syndrome can occur.
■
Minimise your risk of being exposed to vibra-
tions. Maintain the tool according to the in-
structions in the operating instructions.
■
If the tool is used frequently, contact your
dealer to purchase anti-vibration accessories
(e.g. handles).
■
Avoid working with the tool at temperatures
below 10 °C. Define how the vibration load
can be limited in a work plan.
4.8

Noise pollution

A certain level of noise exposure from this appli-
ance is inevitable. Carry out noisy work at ap-
proved and specified time periods. Observe rest
periods as necessary and restrict the duration of
the work to a minimum. For your personal protec-
tion and protection of persons in the vicinity, ap-
propriate hearing protection must be worn.
HTA 4045