General Specifications; Technische Daten - Yamaha EMX5014C Bedienungsanleitung

Reference
Specifications
■ General Specifications
Maximum Output Power
(SPEAKERS)
Total Harmonic Distortion
(THD+N) 20 Hz-20 kHz
Frequency Response
EIN=Equivalent Input Noise
Residual Output Noise
Crosstalk @ 1kHz
Maximum Voltage Gain
@1kHz
Phantom Voltage
Output impedance of signal generator: 150 ohms
Monaural/Stereo channel
Equalizer
± 15 dB (Maximum Variation)
Turn over/roll-off frequency of shelv-
ing, 3 dB below maximum variable
level.
PEAK Indicator
SIGNAL Indicator
FCL Indicator
LEVEL meter
Graphic Equalizer
Internal Digital Effect
Power Amplifier Protection
Power Supply Protection
Cooling
Power Consumption
AC Cord
Dimensions
Weight
*
These specifications apply to rated power supplies of 120V, 230V and 240V
(RL=4 ohms) Both ch drive, 1kHz, THD+N 0.5%
(RL=8 ohms)
(ST, ST SUB, AUX, EFFECT) +14dBu output into 600 ohms
(REC) 0 dBV output into 10 kohms
(ST, ST SUB, AUX, EFFECT) GAIN at minimum level, PAD=OFF, 20Hz-20kHz,
nominal output level @ 1kHz
(SPEAKERS)
(ST OUT) GAIN at maximum level, 20Hz-20kHz
(SPEAKERS)
(ST, ST SUB, AUX)
adjacent inputs
input to output
CH MIC INPUT → SPEAKERS
CH MIC INPUT → ST OUT
CH MIC INPUT → AUX SEND (PRE), ST SUB
CH MIC INPUT → AUX SEND (POST)
CH MIC INPUT → EFFECT SEND
CH MIC INPUT → REC OUT
ST CH 11/12,13/14 → ST OUT
(CHs 1-6, 7/8, 9/10) No load
HIGH 10kHz (shelving)
MID (MONO) 250-5kHz (peaking)
MID (ST) 2.5kHz (peaking)
LOW 100Hz (shelving)
On each channel: indicator lights if post-EQ signal (on ST channels, if either
post-EQ signal or post-mic-amp signal) comes within 3 dB of the clipping level.
On each channel: indicator lights if post-EQ signal (on ST channels, if either
post-EQ signal or post-mic-amp signal) reaches –10 dB.
Input signal level: –75dB
(ST, PFL/AFL) Two 12-points LED level meter (PEAK, +5, +3, +1,0, –1, –3, –5, –7, –10, –15,
–20 dB)
PEAK lights if the signal comes within 3 dB of the clipping level.
(ST OUT) 9 band (63, 125, 250, 500, 1k, 2k, 4k, 8k, 16 kHz) ±12 dB (Maximum Variation)
16 programs, Parameter control
Foot Switch (Internal Effect ON/OFF)
POWER Switch on/off mute
DC-fault: power supply shutdown/manual reset
Thermal/heatsink temp 90˚C: output mute/auto reset
Vl limiter /RL 2 ohms
Clip limiter/THD 1 % , Indicator × 2
Thermal/heatsink temp 100˚C: power supply shutdown/manual reset
Dual variable-speed fan
Length
Height
Depth
Width
< =
> =
< =
> =
> =
.
MIN TYP MAX UNIT
500
350
W
(US,AU)
320
(EU)
0.3 %
0.5 %
–3.0 0.0 1.0 dB
–3.0 0.0 1.0 dB
–128 dBu
–68 dBu
–95 dBu
–68 dB
–68 dB
109 dB
84 dB
80 dB
90 dB
78 dB
62.2 dB
58 dB
48 V DC
MIN TYP MAX UNIT
500 W
2500 mm
155 mm
493 mm
444 mm
10.5 kg
EMX5014C Owner's Manual
32