Technical Data; Before Starting The Equipment - EINHELL RT-MG 12 Li Originalbetriebsanleitung

4. Technical data

Motor supply voltage: ...............................12V DC
Idling speed: .............................. 5000-17000 rpm
Sanding/grinding area: .............. 90 x 90 x 90 mm
Oscillation angle: ..............................................3°
Battery charge voltage: .......................... 12 V DC
Battery charge current: ................................ 0.6 A
Battery charger supply voltage: 230-240 V ~ 50Hz
Charging time: ..........................................3 hours
Battery type: ............................................... Li-Ion
Weight: .......................................................0.8 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 78,5 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 89,5 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_RT_MG_12_Li_SPK1.indb 15 Anl_RT_MG_12_Li_SPK1.indb 15
= 2.970 m/s
2
h
2
- 15 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

5.1 Fitting the plug-in tools (Figures 1/2/3)
•
To fit the plug-in tools safely you should hold
the multifunction tool so that the ON/OFF
switch (1) points down and the tool mounting
(2) faces up.
•
Place the plug-in tool (e.g. the triangular san-
ding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into
the recesses in the plug-in tool.
•
Secure the plug-in tool using the supplied
screw (b) and tighten the screw securely with
the Allen key (9).
•
Make sure that the washer (a) is used for the
screw (b) only in connection with the saw
blade and the scraper (see Figure 3). In this
case the corrugated face of the washer must
be placed against the plug-in tool.
Check that the plug-in tool is secure.
14.04.15 09:53 14.04.15 09:53