Technical Data; Before Using The Equipment; Fitting The Plug-In Tools (Fig. 2-3) - EINHELL TE-MG 12/1 Li Originalbetriebsanleitung

4. Technical data

Motor power supply: ............................... 12 V DC
Idling speed: .............................5000-16500 min
Grinding/sanding area: ............. 90 x 90 x 90 mm
Oscillation angle: ...........................................2.8°
Battery charger output voltage: .............. 12 V DC
Battery charger output current: ....................... 3 A
Battery charger supply voltage:
............................................100-240 V~ 50-60 Hz
Charging time: ..........................................45 min.
Battery type: ............................................... Li-Ion
Number of battery cells: ................................... 3
Battery capacitance: ................................. 2.0 Ah
Weight: .......................................................1.0 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ........................ 78 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 89 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muffs.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specified during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Anl_TE_MG_12_1_Li_SPK9.indb 18 Anl_TE_MG_12_1_Li_SPK9.indb 18
-1
= 7.7 m/s
2
h
2
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before using the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.

5.1 Fitting the plug-in tools (Fig. 2-3)

1. Open the quick-release lock for changing
tools (5) as shown in Fig. 2.
2. Remove the retaining bolt (a).
3. Place the plug-in tool (b) (e.g. the scraper) on
the tool chuck (2) so that the pins of the tool
chuck fit into the recesses in the plug-in tool.
4. Reinsert the retaining bolt (a) as shown in Fig.
3.
5. Close the quick-release lock for changing
tools (5) again. Take care that the pins of the
chuck (2) remain in the recesses in the plug-
in tool.
Check that the plug-in tool is secure!
- 18 -
27.04.2021 09:48:55 27.04.2021 09:48:55
I
t
T
a
p
p
p
W
c
p
s
T
v
Y