Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation and Connection
Pay attention to the information in chapter "Preparations for installation"!
• The LED floodlight can be fixated with the holding bracket using one or several suit-
able screws.
To adjust the holding bracket, loosen the Allen head screws at the left and
right of the holding bracket slightly.
When drilling mounting holes or screwing into place, ensure that no existing
electrical cable, gas or water pipes are damaged.
• For the connection of the power supply of the LED floodlight, a suitable terminal box
or socket is required (both not included in the delivery).
Depending on the installation location of the LED floodlight, the terminal box/socket
must have the appropriate IP protection class.
• Connect the mains cable using the terminals of the LED floodlight (brown cable = L/
phase, blue cable = N/neutral line, green/yellow cable = PE/earth conductor, earth-
ing symbol).
The protective earth wire must be connected!
If the LED floodlight is replacing an existing light and no protective earth
conductor is available, the LED floodlight must not be installed. First, draw a
new mains cable with protective earth.
Where the protective earth is not connected, a fault with the mains voltage
might result in the metal housing of the LED floodlight becoming live. Danger
of electric shock!
Make sure only the minimum required length of the cable is stripped; other-
wise it could cause a short circuit.
• Switch on the mains voltage again and make sure that the LED floodlight is function-
ing.
If you want to adjust the light beam of the LED floodlight, loosen the Allen
head screws to the left and right of the holding bracket first. Then, adjust the
orientation LED floodlight as desired and re-tighten the Allen head screws.
If the LED floodlight is not lit up, switch off the mains voltage immediately
from all poles (take out the fuse or switch off the automatic cut-out, switch
off the earth fault circuit interrupter).
Then check the connection for the LED floodlight.
In case of doubt, contact a professional (e.g., an electrician)!
Technical Data
Operating voltage............................... 220 - 240 V/AC, 50/60 Hz
Protection class ................................. I
Protection class ................................. IP65
Irradiation angle ................................. 90°
Number of LEDs.................................. 1 (firmly mounted, not replaceable)
Dimmable............................................. no
Length of power cable ...................... approx. 1.2 m
Ambient conditions ............................ Temperature -20°C to +45°C, relative air humidity
Item No.
1193603
Power input
10 W
Light colour
6000 K (cold-white)
Luminous flux
800 lm
Dimensions
165 x 55 x 193 mm
(holding bracket in
180°-position),
W x D x H
Dimensions
165 x 85 x 181 mm
(holding bracket in
180°- position),
W x D x H
Weight
0.9 kg
Slight variations in dimensions and weight are dependent on the production technique.
10% - 90% (not condensing)
1180552
10 W
3200 K (warm-white)
800 lm
165 x 55 x 193 mm
165 x 85 x 181 mm
0.9 kg
Maintenance and Cleaning
The product is maintenance-free. Repair or maintenance work must be carried out by
a specialist. The LED bulb is permanently installed and cannot be replaced.
Before cleaning, turn off the mains voltage for the LED floodlight and let it cool down
sufficiently.
You can use a clean, dry, soft cloth for cleaning. In case of heavier soiling, you can
moisten the cloth with clean water.
Do not use aggressive, chemical or scouring cleaning agents, as this may lead to dis-
colouration or scratch marks.
Never direct a stream of water from a garden hose or a high-pressure cleaner onto
the LED floodlight!
Disposal
The product must not be disposed of in the household waste.
Dispose of the product at the end of its serviceable life in accordance with
the current statutory requirements; e.g., return it to any suitable collection
point
1180553
1193638
30 W
30 W
6000 k (cold-white)
3200 K (warm-white)
2700 lm
2600 lm
247 x 77 x 309 mm
247 x 77 x 309 mm
247 x 120 x 292 mm
247 x 120 x 292 mm
2.9 kg
2.9 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
1180556
1180588
50 W
50 W
6000 K (cold-white)
3200 K (warm-white)
4500 lm
4400 lm
326 x 106 x 396 mm
326 x 106 x 396 mm
326 x 175 x 357 mm
326 x 175 x 357 mm
4.9 kg
4.9 kg
Werbung
Inhaltsverzeichnis
