THOMSON ROC3205SE Bedienungsanleitung Seite 2

Downloaded from www.Manualslib.com
Operating Instruction
This universal remote control is compatible with the majority of television sets, DVD
players, satellite receivers and infrared controlled cable. This remote control has already
been programmed so that you can use it to control most of the audio/video products
made by the THOMSON group. Before attempting to programme the remote control, try it
out by using one of the methods described in this user manual.The two CR2032 batteries
are already fi tted in the remote control. Refer to the diagram on the cover to replace
them when they are worn out. Please keep this guide along with the code list (provided
separately), so that you can programme your remote control for use with other products.
Description of the key functions
1 Indicator lamp: the red indicator lamp
lights up when any key is pressed.
2 Product keys (TV, DVD or SAT): Used
to programme and control different
products (TV, satellite receiver, DVD
player and so on).
3 SHIFT: activates the secondary key
features (indications in blue).
4 VOL-, VOL+ Increases (+) or decreases
(-) the volume of the TV set; SHIFT +
A/B: also allows you to navigate the
menus horizontally.
5 Teletext On/Off in TV mode.
SHIFT + MENU: turns on the menu of
the selected products
6 E (rewind): Goes backward or
advances forward (DVD)*.
7 RECORD: To record, press the
RECORD key twice.
8 Stop the disc (DVD)*.
9 Number keys 0 to 9: these keys have
the same functions as those of your
original remote and are also used to
enter the codes for different products.
10 stop page scrolling (videotext).
11 SETUP: Programmes the remote
control.
4
manuals search engine
Testing the remote control
before you programme it
1. Turn on the product you want to
2. Press the product key (2) that
12 POWER: On/Standby.
13 AV: For selecting an external source 3. Point the remote control towards
(SCART).
14 PROG+, PROG-: Programmes zapping
button (received by the television set
or the satellite receiver); use to scroll
vertically through menus. SHIFT +
C/D: also allow you to navigate the
menus vertically.
15 MUTE: Switches the TV sound off. Programming the remote control
SHIFT + OK: confi rms a selection.
Method A – Fast programming
16 Teletext Off in TV mode.
with 1-digit subcode
SHIFT + EXIT: turns off the menu of the
selected product.
17 B (play): play a DVD disc DVD*. Before you start programming, you
18 F fast forward (DVD)*. must fi nd the subcode
19 J: Suspends play and stops on an of the product to be controlled
image*. (television set, satellite
20 Videotext inlay on TV picture. receiver or DVD player).
Refer to the list provided with these
21 Press this key fi rst before you type in
instructions, page I of
the 2-digit channel number (except for
Thomson group products). the codes.
1. Turn on the product you want to
* The coloured buttons can be used
to select categories when teletext is 2. Hold down the SETUP (11) key
activated, and specifi c
functions depending on the make.
3. Press the product key (2) that
corresponds to the type of
product you want to control:
TV: television set, DVD: DVD
control. player, SAT: satellite receiver.
4. While the indicator is lit, type
corresponds to the type of in the subcode (example: 1 for
product you want to control: THOMSON).
TV: television set, DVD: DVD 5. Point the remote towards the
player, SAT: satellite receiver. product and try to turn it off by
pressing the POWER (12) key.
the product and try to turn it off 6. If the product you want to control
by pressing the POWER (12) key. turns off, press the MUTE (15) key
If the product doesn't turn off, to save the subcode.
you'll need to programme the 7. If the product doesn't turn off,
remote control by one of the press the POWER (12) key
methods described in chapter 3. repeatedly until the set switches
off. Wait approximately one
second between key presses to
give the red indicator lamp (1)
enough time to go off and light up
again. This will allow you to see
whether the product responds or
not.
8. Immediately after the product
to be controlled turns off, press
the MUTE (15) key to save the
subcode.
Note:
If you want to assign another type
of product than those mentioned
control. on the remote control (with the
exception of the TV button which
until the red indicator lamp (1) can only be used to control a
remains lit (the indicator light television set), begin by entering
remains on for a few seconds to the code that corresponds to the
give you the time to proceed with product you want to programme (a
the following steps. The indicator 4-digit code that you will fi nd in the
lamp fl ashes when this time is code booklet – see method B).
almost up, and then goes off).
5