Specifications; Functional Description - Makita 9403 Betriebsanleitung

ENGLISH
(Original instructions)
1 Lock button
2 Switch trigger
3 Lever
4 Adjusting knob
5 Dust bag

SPECIFICATIONS

Model
Belt size ............................................... 100 mm x 610 mm
Belt speed .......................................................500 m/min
Overall length ......................................................353 mm
Net weight ............................................................. 5.7 kg
Safety class ................................................................ /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
BELT SANDER SAFETY WARNINGS
1. Hold power tool by insulated gripping surfaces,
because the belt may contact its own cord. Cut-
ting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
2. Ventilate your work area adequately when you
perform sanding operations.
3. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
4. Always use the correct dust mask/respirator for
the material and application you are working
with.
5. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
6. Hold the tool firmly with both hands.
7. Make sure the belt is not contacting the work-
piece before the switch is turned on.
4
Explanation of general view
6 Dust spout
7 Fastener
8 Steel plate
9 Carbon plate
8.
9.
9403
10. This tool has not been waterproofed, so do not
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
ENE052-1

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
ENF002-2
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
GEA010-1
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
ASSEMBLY
CAUTION:
GEB015-3
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing abrasive belt (Fig. 2 & 3)
Pull the lever all the way out and install the belt over the
rollers, then return the lever to the original position.
CAUTION:
• When installing the belt, make sure that the direction of
the arrow on the back of the belt corresponds to the
one on the tool itself.
Adjusting belt tracking (Fig. 4)
While the belt is running, use the adjusting knob to center
the belt tracking. Failure to do so can result in frayed belt
edges and wear on the sander frame.
10 Strap washer
11 Limit mark
12 Brush holder cap
13 Screwdriver
Keep hands away from rotating parts.
Do not leave the tool running. Operate the tool
only when hand-held.
use water on the workpiece surface.