Intended Use; Angle Grinder Safety Warnings - Ryobi Rag750-115 Übersetzung Der Originalanleitung

Safety, performance, and dependability have been given top
priority in the design of your angle grinder.

INTENDED USE

The angle grinder is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual and can be considered responsible for their
actions. The angle grinder is designed for grinding and
cutting metals only. Only appropriate grinding discs as
designed for handheld use; it is not to be mounted onto a
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

SAFETY WARNINGS COMMON FOR GRINDING OR
ABRASIVE CUTTING-OFF OPERATIONS:
This power tool is intended to function as a grinder
or cut-off tool. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool. Operations for which the power
tool was not designed may create a hazard and cause
Do not use accessories which are not specifically
designed and recommended
manufacturer. Just because the accessory can be
attached to your power tool does not assure safe
operation.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange. Accessories that to do
not match the mounting hardware of the power tool will
loss of control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
or respirator must be capable of filtrating particles
high intensity noise may cause hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a "live" wire
Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
Never lay the power tool down until the accessory
has come to a complete stop. The spinning accessory
by the tool
may grab the surface and pull the power tool out of your
control.
Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into your
body.
Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
electrical hazards.
Do not operate the power tool near flammable
materials.
Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
protective equipment.
Original Instructions
EN
FR
DE
Fragments of
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
1