Technical Data; Noise And Vibration Values - Scheppach DP18VARIO Originalbetriebsanleitung

Technical Data

Nominal input voltage
Power rating
Motor speed
Output speed (infinitely adju-
stable)
Drill chuck mount
Spindle taper
Drill chuck
Dimensions of drill table
Angle adjustment of table
Drill depth
Pillar diameter
Height
Weight
Laser class
Wavelength of laser
Laser output

Noise and vibration values

The total noise values determined in accordance with
EN 61029.
sound pressure level - no load L
sound pressure level - load L
uncertainty K
pA
sound power level - no load L
sound power level - no L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
Vibration emission value ah = 1.7 m/s
K uncertainty = 1,5 m/s
2
The specified vibration value was established in
accordance with a standardized testing method. It may
change according to how the electric equipment is used
and may exceed the specified value in exceptional
circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Assembly
Column and machine foot, Fig. 3
1. Set the machine foot (1) down on the ground or the
workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the four hexagonal screws (19) to fasten the
column into the base plate and tighten them using
a hexagon spanner (A).
20 І 80
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
230-240V~ 50Hz
550W
1450min
-1
440 - 2580 min
-1
B16
MT2
1 - 16mm
240 x 240mm
45° - 0° - 45°
80mm
65mm
713mm
38.5kg
2
650mm
1mW
70.2 dB(A)
pA
73.5 dB(A)
pA
3 dB(A)
82.7 dB(A)
WA
86.3 dB(A)
3 dB(A)
2
Removing the rack, Fig.4
In order to install your drill, you must first remove the
rack (E)
1. Use an Allen key (WAF3) to remove the ring (F)
and pull this off the column (2).
2. Now pull the rack (F) out.
Pre-installing the drilling table holder, Fig.5+6
1. Push the crank holder (20) through the hole in the
drilling table holder (18) from the inside.
2. Put the crank handle (17) on the crank holder and
use the Allen key (3) to secure the crank handle
(17).
Installing the drilling table holder, Fig.7+8
1. Insert the rack (E) into the groove on the drilling
table holder (18).
2. Align the rack (E) centrally in relation to the drilling
table holder (18).
3. When bringing the rack (E) together within the
groove, ensure that the tooth meshing between the
rack and the drilling table holder (18) is correct.
4. Now place the drilling table holder (18) with the
rack (E) on the column (2) and guide the rack (E)
into the bottom rack guide on the column foot.
5.
Use the ring (F) to secure the rack (E). Ensure that
the rack guide on the ring (F) is pointing down-
wards. Tighten the integrated Allen screw to affix
the ring (F).
6.
Screw one of the clamping handles (3) into the
drilling table holder (18).
Installing the drilling table, Fig.5
1. Insert the drilling table (4) into the drilling table
holder (18).
2. Use a clamping handle (3) to secure the drilling
table (4).
3. Insert the roller support (13) into the receptacle on
the drilling table (4) and use the wing screws (21)
to secure it.
Installing the machine head and column, Fig. 10
1. Place the machine head (14) on the column (2).
2.
Align the drill's spindle with the table and the base
plate and tighten the Allen screw that is located on
the side of the machine head. (Allen key WAF4 / C)
Installing the handles, Fig. 11+12
1. Screw three handles (10) tight in the handle
bracket's thread. Use the hexagon spanner (A) to
do this.
2. Screw the remaining handle (10) into the handle
bracket for speed adjustment. Use the hexagon
spanner (A) to do this.
Installing the folding swarf protector and the drill
chuck, Fig.13
1. Push the folding swarf protector (11) onto the spin-
dle on the machine head and use a Phillips head
screwdriver to secure it.
2. Push the tapered mandrel (22) into the drill chuck
(12) with a sharp jolt.
3. Then push the tapered mandrel (22) into the drill
spindle. To do this, guide the drill chuck (12) includ-
ing the cone (22) into the spindle until is reaches
the stop and then turn it until it slides a little further
into the spindle. Now insert the drill chuck (12)
including the cone into the spindle. Check that it is
tight.
Important: All bare parts are greased in order to protect
them from corrosion. Before mounting the drill chuck
(12) onto the spindle, both parts must be completely