Maintenance; Optional Accessories - Makita DUB142 Betriebsanleitung

• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Switch action
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released. (Fig. 2)
To start the tool, simply pull the switch trigger. Air volume
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
Air volume adjusting dial
Air volume can be adjusted to any of three settings by
turning the adjusting dial with the switch trigger fully
depressed. Refer to the table below for the relationship
between the number on the dial and the air volume.
Number on the dial
3
2
1
008312
CAUTION:
• Use the adjusting dial only after the switch trigger
returns to the "OFF" position. Turning the dial before
the trigger returns may damage the tool.
• If the tool is operated continuously until the battery
cartridge has discharged, rest the tool for at least 15
minutes before proceeding with a fresh battery.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Blowing (Fig. 3)
For dust blowing, attach nozzle to blower outlet, turning
clockwise to lock it in place.
To remove the nozzle, turn it counterclockwise.
Dust suction (Fig. 4)
For dust suction, fit nozzle onto suction inlet and dust bag
onto blower outlet.
After the bag fills with dust, empty the contents of the dust
bag into a dust bin by releasing the fastener. (Fig. 5)
CAUTION:
• Empty the dust bag before it becomes too full, or the
suction force weakens.
NOTICE:
The garden nozzle (optional accessory) is intended for
blowing use only. Do not use garden nozzle for suction.
6
Air volume
High
Medium
Low

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning
From time to time, wipe off the outside of the tool using a
cloth dampened in soapy water. Never use gasoline,
thinner or the like, or discoloration and/or cracks can take
place. (Fig. 6)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Nozzle
• Garden nozzle
• Dust bag
• Corner nozzle
• Straight pipe
• Flexible hose
• Joint
• Makita genuine battery and charger
NOTICE:
The garden nozzle is intended for blowing use only. Do
not use garden nozzle for suction. Debris may become
clogged and result in damaging the blower.
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745, EN15503:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745, EN15503:
Work mode: operation without load
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
ENG905-1
): 85 dB (A)
pA
): 95 dB (A)
WA
ENG900-1
2
): 2.5 m/s or less
h
2
ENG901-1