Ryobi RC18ASV Übersetzung Der Originalanleitung Seite 6

EN ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given
top priority in the design of your battery charger.
INTENDED USE
The charger is intended only to charge the compatible
battery packs attached to compatible stick vac model(s)
listed in this operator's manual.
The product must be mounted on a wall before the stick vac
or any other accessory is attached to it.
The product is only for indoor use, in dry conditions.
The product is not intended to charge any other type of
battery or be used as a power supply. It should never be
Do not use the product for any other purpose.
CHARGER SAFETY WARNINGS
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Do not recharge primary cells (non-rechargeable).
The product must not be damp and should never be
used in a damp environment.
The product is for indoor use only.
Do not cover any ventilation slots, and provide adequate
ventilation during operation.
Mains voltage must correspond with the voltage
specifications on the product.
Before using the product, check that the charger
enclosure, cable, and plug are not damaged. If damage
is found, do not use the product and bring it to an
authorised service centre for repair.
Do not use the product if it has suffered any heavy shock
or jolting, or if it is damaged in any other way.
When charging, do not expose the product to sunlight
or other heat source. The recommended temperature
range at charging vicinity is 10 °C to 25 °C.
Due to the heat generated during charging, do not use
the product on a combustible surface.
Do not use the product near flammable materials,
such as cloth, packaging materials, paint, spray paint
or aerosols, lubricants, thinners, petrol containers, gas
containers, or gas appliances.
Never modify, disassemble, or attempt to repair the
product yourself.
Do not allow the charger or battery packs to become
contaminated with any material that could be conductive,
such as metallic particles from grinding, cutting, or
machining processes.
Protect the battery contact terminals from metallic
objects to avoid a short circuit, which can cause fire or
explosion.
6
Unplug the product from the power socket when it is not
in use or when cleaning it.
Use only an extension cable that is approved and in
good condition.
Do not charge battery packs that show signs of leaks.
Dispose of them properly.
Never charge a damaged battery pack. Replace
damaged battery packs immediately.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack, or charger in fluid or allow fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
WALL MOUNTING
Carefully select a stable wall for mounting the charger.
Make sure that there is no hindrance to mounting
work or operation. The maximum gross weight of the
charger with compatible stick vac, accessories, and
heaviest battery is approximately 7 kg. Provide sufficient
reinforcement for the wall if necessary.
Mount the charger in a horizontal orientation only.
Install four screws on the wall to mount the charger.
Otherwise, the charger may fall and cause serious
injury.
Check the tightness of the screws on a regular basis.
Make sure that the of the screws fit properly in the
wall mounting holes to hold the charger firmly in place.
Otherwise, the charger may fall because of loose
screws.
OPERATION
CHARGING THE BATTERY PACK
Battery packs are shipped in a low charge condition.
Therefore, you should charge them before first use.
If the charger does not charge the battery pack under
normal circumstances, bring both the battery pack and
charger to an authorised service centre.
Make sure that the power supply is normal household
voltage, 220–240V, 50/60Hz, AC only.
Make sure that the battery pack latch clicks into place on
the stick vac, and that the stick vac is stably mounted on
the charger before charging.
NOTE: The charging times listed on the compatible battery
packs table can vary depending on the type of the battery
pack used(e.g., RB18L40, RB1840X, RB1840T).