Before Use; Operation - Hilti VCD50L Bedienungsanleitung

● Check the appliance for any damage. All parts of the
appliance must be checked carefully to ensure correct,
faultless functionality before further use.
● Damaged switches must be replaced at a Hilti service
centre. Do not use the appliance if it cannot be switched
off and on properly.
● If necessary, have the appliance repaired by an elec-
trical specialist (Hilti service department).
● To avoid risk of accident, use only original Hilti spare
parts.
● Insert the supply cord plug in the socket only when
the appliance is switched off.
● In the event of a power cut: switch the appliance off
and unplug the supply cord.
● Avoid using extension cords with multiple sockets and
operating several appliances simultaneously.
● The connections used for supply cords, extension
cords or electric tool connecting cables must offer pro-
tection from sprayed water.
● To ensure safety, the appliance may be serviced or
repaired only at an authorised Hilti repair centre.
● When an IPX4 plug is not used at the appliance pow-
er socket, the vacuum cleaner may not be exposed to
rain and must be stored in a dry place.
5.9 Requirements to be met by the user
● The appliance is intended for professional use.
● The appliance may be operated, serviced and repaired
only by authorised, trained personnel. This personnel
must be informed of any special hazards that may be
encountered.
5.10 Personal protective equipment
● The user requires no personal protective equipment.

6. Before use

It is essential that the safety precautions printed in these
operating instructions are read and observed.
6.1 Transport
● When moving the appliance, bring the transport han-
dle into the extended position and lock it in place with
the sleeves.
● Hang the hose and supply cord over the transport
handle.
● The total permitted weight must not exceed 60 kg.
6.2 Attaching the Hilti toolbox or the Hilti DPC 20 to
the appliance
1. Slide the toolbox or the DPC 20 into the guides on the
rear of the appliance.
12
Printed: 07.07.2013 | Doc-Nr: PUB / 5071296 / 000 / 00
2. Press the toolbox or the DPC 20 toward the appliance
until it engages.
6.3 Releasing the Hilti toolbox or the Hilti DPC 20 from
the appliance
1. Push the locking mechanism upwards.
2. Remove the toolbox or the DPC 20 from the guides
on the appliance.
6.4 Preparing the appliance for inital use
The appliance may not be plugged into an electric sup-
ply when any kind of adjustments or maintenance work
are being carried out.
Labels in the local language displaying the warning for
dust class L are supplied inside the appliance. You should
select the warning label in your local language and apply
it over the English warning text on the dust class L label
already attached to the rear of the top section of the vacuum
cleaner.
The accessory items are supplied in the container
and must be removed before the appliance is used for
the first time.
1. Extend the transport handle into the upright position
»
´
2. Open the latch
3. Lift off the top section of the appliance
4. Remove the disposal bag holder
5. Remove the small tapered adaptor for Hilti diamond
cutters and Hilti dry-cutting diamond coring machines
6. Remove the disposal bag
7. Fit the disposal bag
8. Attach the disposal bag sleeve
²
socket
9. Insert the disposal bag holder
10. Fold over the edge of the disposal bag
11. Fit the top section
´
12. Close the latch
13. Connect the end of the hose
¸ to the hose socket.
connector
NOTE: The disposal bag must always be folded over
the disposal bag holder inside the container.

7. Operation

It is essential that the safety precautions printed in these
operating instructions are read and observed.
7.1 Connecting to the mains supply
The voltage provided by the mains supply must corre-
spond to the voltage rating printed on the type plate.
The appliance must be switched off (switch position 0).
1. Insert the mains plug in the socket.
³
¹
to the hose
¹
III.
³ onto the container
¾ with the rotating
·
·