Care And Maintenance - Hilti VCD50L Bedienungsanleitung

7.2 Appliances without an electric tool socket
Turn the switch to the "MAN" position. The appliance then
starts immediately (soft start function).
7.3 Appliances with an electric tool socket
"MANUAL" operation of appliances equipped with an
electric tool socket
Turn the switch to the "MAN" position. The appliance then
starts immediately (soft start function).
Connecting electric tools to the electric tool socket
1. Turn the switch to the "0" position.
2. Disconnect the supply cord plug from the socket.
3. Switch the electric tool off.
4. Check the maximum power input rating of the electric
tool to be connected (observe the data given in the
"Technical data" and the information printed at the elec-
tric tool socket.
5. Connect the electric tool to the electric tool socket.
6. Insert the mains plug in the socket.
"AUTO" operation of appliances equipped with an elec-
tric tool socket
NOTE Before turning the switch to the "AUTO" position,
check that the electric tool connected to the electric tool
socket is switched off.
Turn the switch to the "AUTO" position.
The appliance then starts automatically approx. 5 sec-
onds after the electric tool connected to it is switched
on. When the electric tool is switched off, the appliance
switches off automatically after a short delay.
7.4 After finishing work
1. Switch the electric tool off.
2. Turn the switch to the "0" position.
3. Disconnect the mains plug from the socket.
4. Roll up the hose and the supply cord.

8. Care and maintenance

8.1 Cleaning the filter
The filter is cleaned automatically during operation.
Nevertheless, should it become heavily soiled, complete
cleaning is necessary.
1. Switch the appliance off.
2. Hold the hose in the hand.
3. Use one hand to close off the end of the hose.
4. Turn the switch to the "MAN" position and, using the
hand to close off the end of the hose, allow the appli-
ance to run for 10 seconds.
In addition to this, the filter may be cleaned with water
and a cloth (do not use a high-pressure cleaning sys-
tem). Mineral dust may clog the filter, reducing its suc-
tion performance, if it is not cleaned adequately.
Printed: 07.07.2013 | Doc-Nr: PUB / 5071296 / 000 / 00
Don't knock the filter against a hard object or use a hard
or pointed object to clean it. This reduces the life of the
filter.
8.2 Changing the disposal bag
Removing the bag
1. Open the latch.
2. Lift off the top section.
3. Remove the disposal bag holder.
4. Close the disposal bag.
5. Pull the disposal bag sleeve from the hose socket and
use the cover provided to close the opening in the dis-
posal bag.
6. Use the cable tie supplied to close the disposal bag.
7. Remove the disposal bag and dispose of it in accor-
dance with national and local regulations.
Inserting the bag
1. Fit the disposal bag.
2. Attach the disposal bag sleeve to the hose
socket.
3. Insert the disposal bag holder.
4. Fold the edge of the disposal bag over.
5. Fit the top section onto the container.
6. Close the latch.
8.3 Changing the filter
Removing the filter
1. Open the latch.
2. Lift off the top section of the appliance and lay it down
with the filter facing upwards.
3. Release the two wing screws.
4. Pull off the filter retaining disc.
5. Pull off the filter.
Fitting the filter
1. Push on the new filter as far as it will go.
2. Fit the filter retaining disc.
3. Insert and tighten the two wing screws.
4. Fit the top section onto the appliance.
5. Close the latch.
8.4 Changing the cooling air filter
1. Pull the cooling air filter out of the grip depression in
the appliance.
2. Fit the new cooling air filter into the grip depression in
the appliance
13