Upright SL26 Betriebsanleitung Seite 8

Routine Service
Use the following table as a guide for routine
maintenance. Inspection and maintenance shall
be performed by personnel who are trained and
familiar with mechanical and electrical proce-
dures. Refer to the Service Manual for complete
service instructions.
Please copy this page and use the Routine Service
Table as a checklist when inspecting a machine for
service.
COMPONENT INSPECTION OR SERVICES
Engine Oil Check level and condition
Check for leaks
Change oil & filter
Engine Fuel Check fuel level
System Check for leaks
Replace fuel filter
Check air cleaner
Engine Check electrolyte level
Battery Check specific gravity
System Clean exterior
Check battery cable condition
Clean terminals
Engine Check coolant level (with engine cold)
Coolant Replace coolant
Hydraulic Oil Check oil level
Change filter
Drain and replace oil
Hydraulic Check for leaks
System Check hose connections
Check hoses for exterior wear
Emergency Open the emergency lowering
Hydraulic valve and check for
System serviceability
Controller Check switch operation
Control Check the exterior of the cable
Cable for pinching, binding or wear
Platform Check fasteners for proper torque
Deck and Check welds for cracks
Rails Check condition of deck
Tyres Check for damage
Check lug nuts/bolts,
torque to 123 Nm (90 ft. lbs.)
Hydraulic Wipe clean
Pump Check for leaks at mating surfaces
Check for hose fitting leaks
Check mounting bolts for proper torque
Check the drive coupling for proper
alignment and wear
Lubricate pump splines
Drive Motors Check for operation and leaks
Steering Check hardware & fittings for proper torque
System Grease pivot pins
Oil king pins
Check steering cylinder for leaks &
mounting bolts for proper torque
Elevating Inspect for structural cracks
Assembly Check pivot points for wear
Check mounting pin pivot bolts
for proper torque
Check linkage gear for wear
Check elevating arms for bending
Grease linkage pins
Grease linkage gear
Routine Service Table Key
Interval
Daily=each shift (every day) or every eight hours
30d=every month (30 days) or every 50 hours
3m=every 3 months or 125 hours
6m=every 6 months or 250 hours
1y=every year or 500 hours
2y=every 2 years or 1000 hours
Y=Yes/Acceptable
N=No/Not Acceptable
R=Repaired/Acceptable
INTERVAL Y N R COMPONENT INSPECTION OR SERVICES
Daily Chassis
Daily
100
HOURS
Daily Lift
Daily Cylinder
6
M
Daily
Daily
30
D
6
M
Daily Fore/Aft
6 Cylinder
M
Daily
3
M
Daily
6
M
2 Side/Side
Y
Daily Cylinder
30
D
30
D
Daily
Axle
Daily Cylinder
Daily
Daily
Daily
Daily Bubble Level Check bubble and target ring for damage.
Daily Entire
30 Unit
D
30
D
30
D
Daily
30 Labels
D
1
Y
6
M
Daily
6
M
30
D
30
D
30
D
Service Report
Daily
30
D
Date: ______________
30
D
Owner: ________________________________
6
M
6
M Model No: ____________ Serial No: _________
30
D
30
Serviced By: ____________________________
D
Service Interval: _________________________
8
Check hoses for pinch or rubbing points
Check component mounting for proper torque
Check welds for cracks
Check the cylinder rod for wear
Check mounting pin pivot bolts
for proper torque
Check pivot pin snap rings
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Check the cylinder rod for wear
Check mounting pin pivot bolts
for proper torque
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Check the cylinder rod for wear
Check mounting pin pivot bolts
for proper torque
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Check the cylinder rod for wear
Check mounting pin pivot bolts
for proper torque
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Check for and repair
collision damage
Check fasteners for proper torque
Check for corrosion-remove
and repaint
Lubricate
Check for peeling, missing, or unreadable
labels & replace
INTERVAL Y N R
Daily
6
M
Daily
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
30
D
Daily
Daily
3
M
6
M
30
D
Daily