Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications - Makita GA5030 Betriebsanleitung

Winkelschleifer
Vorschau ausblenden Andere Handbücher für GA5030:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 17
ENGLISH (Original Instructions)
1.
Shaft lock
2.
Switch lever
3.
Wheel guard
4.
Screw
5.
Bearing box
6.
Lever
7.
Lock nut
8.
Depressed center grinding wheel/
Multi-disc

SPECIFICATIONS

Model
Depressed center wheel diameter
Spindle thread
Rated speed (n)/No load speed (n
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
.. Read instruction manual.
............. DOUBLE INSULATION
... Wear safety glasses.
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
4
Explanation of general view
9.
Inner flange
10. Lock nut wrench
11. Abrasive cut-off wheel/diamond
wheel
12. Wheel guard for abrasive cut-off
wheel/diamond wheel
13. Abrasive cut-off wheel
14. Diamond wheel
GA4030
100 mm
M10
)
11,000 min
0
266 mm
1.7 kg
Save all warnings and
END202-6
instructions for future reference.
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
ENE048-1
2. Operations such as polishing are not
ENF002-2
3. Do not use accessories which are not specifically
4. The rated speed of the accessory must be at least
GEA010-1
5. The outside diameter and the thickness of your
15. Thickness: Less than 4 mm
(5/32")
16. Thickness: 4 mm (5/32") or more
17. Exhaust vent
18. Inhalation vent
GA4530
115 mm
M14 or 5/8"
(country specific)
-1
11,000 min
266 mm
1.8 kg
/II
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
GA5030
125 mm
M14 or 5/8"
(country specific)
-1
11,000 min
266 mm
1.8 kg
GEB033-6
-1

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis