Scheppach BTR6500 Originalbetriebsanleitung Seite 27

• Please do not tilt the construction dryer more than
45°, neither during transport nor during use.
• If the construction dryer has been accidentally tilt-
ed, wait at least 12 hours before using the construc-
tion dryer.
10. Maintenance & Cleaning
The product is designed for problem-free operation
and minimal monitoring.
All moving parts are permanently lubricated.
There are no other parts inside the product that re-
quire maintenance.
Cleaning
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub
the product clean with a clean cloth or blow it off
with compressed air at low pressure.
• Remove the water tank (7) and pour the water into a sink.
Dry the inside and outside of the water tank (7)
thoroughly before inserting it.
It is advisable to clean the water tank (7) regularly
every fortnight to prevent mould and bacteria. To do
this, fill the water tank (7) with lukewarm water and
add a commercially available washing-up liquid.
Rinse several times with lukewarm water. It is also
advisable to carry out disinfection after cleaning.
Use a commercially available alcohol-based disin-
fectant or high-proof alcohol. Both substances are
completely harmless if rinsed several times with
lukewarm water afterwards.
• Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
agents or solvents; they could corrode the plastic
parts on the product. Ensure that no water can pen-
etrate the interior of the product.
11. Transport
Transport the construction dryer upright to prevent
damage to the compressor. The water tank (7) must
be emptied before transport.
If you transport the construction dryer horizontally,
the construction dryer must stand upright for at least
four hours before use.
12. Storage
Store the product and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
Store the product in a room without continuously oper-
ating ignition sources (e.g. open flames, an operating
gas appliance or an operating electric heater).
The optimum storage temperature lies between 5 and
30 ˚C.
Store the product in its original packaging. Cover the
product to protect it from dust or moisture. Store the
operating manual with the product.
13. Repair & ordering spare parts
After repairs or maintenance, make sure that all safe-
ty-related parts are installed and are in perfect con-
dition. All parts which may cause injury must be kept
where they are inaccessible to children or others.
Attention: According to the German Product Liabili-
ty Act, no liability is accepted for damage caused by
improper repairs or by not using original spare parts.
Such work should be performed by a customer ser-
vice centre or an authorised specialist. The same ap-
plies to accessory parts.
Spare parts and accessories can be obtained from
our Service Centre. To do this, scan the QR code on
the front page.
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the event
of any queries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
Important note in the case of repairs:
For return delivery of the product for repair, please
ensure for safety reasons that it is free of oil and fuel
when it is sent to the service centre.
13.1 Ordering spare parts
Please provide the following information when order-
ing spare parts:
• Model designation
• Item number
• Type plate data
Spare parts / accessories
Water tank - item no.:
Wheels - item no.:
Wheel axle - item no.:
13.2 Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*: Support foot, wheels, drain hose,
hose clamp
www.scheppach.com
5906501003
5906501016
5906501021
GB | 27