Atlas Copco SP2000 Sicherheitshinweise Seite 4

Safety Information
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE directive/regulations. The
entire product, or the WEEE parts, can be sent to your "Cus-
tomer Center" for handling.
Information Regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
electrical and mechanical components in the product may
contain lead metal. This is in compliance with current sub-
stance restriction legislation and based on legit exemptions in
the RoHS Directive (2011/65/EU). Lead metal will not leak
or mutate from the product during normal use and the concen-
tration of lead metal in the complete product is well below the
applicable threshold limit. Please consider local requirements
on the disposal of lead at product end of life.
UK DECLARATION OF CONFORMITY
We, Tentec Ltd. C/O Atlas Copco Bolt Tighten-
ing Solutions, Unit F1, Innovation Drive, Pende-
ford, Wolverhampton, England, WV9 5GA, de-
clare under our sole responsibility that the prod-
uct (with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
S.I. 2008/1597, S.I. 2012/3032, S.I. 2016/1091
Designated Standards applied:
BS EN ISO 12100:2010, BS EN ISO 4413:2010
Authorities can request relevant technical information from:
Jonathan Gibbs, Quality Manager, Atlas Copco Bolt Tighten-
ing Solutions, Unit F1, Innovation Drive, Pendeford, Wolver-
hampton, England, WV9 5GA
Wolverhampton, 14 August 2024
Nicholas Evans, General Manager
Signature of issuer
4 © Atlas Copco Industrial Technique AB - 9839 2552 00
Regional Requirements
WARNING
This product can expose you to chemicals including lead,
which is known to the State of California to cause cancer
and birth defects or other reproductive harm. For more
information go to
https://www.p65warnings.ca.gov/
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the product
cease to be legible or become detached, replace without
delay.
• The product must only be installed, operated and serviced
by qualified personnel in an industrial environment.
Safety Signal Words
The safety signal words Danger, Warning, Caution, and
Notice have the following meanings:
DANGER DANGER indicates a hazardous situation which,
if not avoided, will result in death or serious in-
jury.
WARN- WARNING indicates a hazardous situation
ING which, if not avoided, could result in death or
serious injury.
CAUTION CAUTION, used with the safety alert symbol,
indicates a hazardous situation which, if not
avoided, could result in minor or moderate in-
jury.
NOTICE NOTICE is used to address practices not related
to personal injury.
SP-2000