Herunterladen Diese Seite drucken

Atlas Copco ITB-A61-100-13-HMI Sicherheitshinweise Seite 7

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 17
ITB-A61-100-13-HMI
"click" torque wrenches do not check for potentially dan-
gerous over-torqued conditions. Over-torqued or under-
torqued fasteners can break, loosen or separate. Released
assemblies can become projectiles.
• Use only power or impact sockets in good condition.
Do not use hand sockets.
• When using a power tool, the operator may feel dis-
comfort in the hands, arms, shoulders, neck, or other
parts of the body. Vary between appropriate postures
throughout the work day, maintain a secure footing and
avoid awkward or off-balance postures.
• Repetitive work motions, awkward positions and ex-
posure to vibration can be harmful to hands and
arms. If numbness, tingling, pain or whitening of the skin
occurs, stop using tool and consult a physician.
• Take caution when operating in confined spaces. Be-
ware of crushing hands between tool and workpiece.
• High sound levels can cause permanent hearing
loss.Use hearing protection as recommended by your em-
ployer or occupational health and safety regulations.
• Ensure that the workpiece is securely fixed.
• Proceed with care in unfamiliar surroundings. Be
aware of potential hazards created by your work activity.
This tool is not insulated from coming into contact with
electric power sources.
Tools containing a clutch: Never use the product without
making sure the clutch releases. Immediately after adjusting
the clutch, check for correct operation.
Tools used together with a reaction bar: Never put your
hand near or close to the reaction bar while the tool is being
used. Be aware of the rotational direction of the spindle be-
fore starting the tool, the reaction force may work in an unex-
pected direction with risk of crushing injuries.
WARNING Crushing Hazard
Check the rotational direction of the tool before start! A
start in an unexpected rotational direction can cause bod-
ily injury or property damage. Moving parts can crush
and cut.
Make sure that the rotational direction of the tool is
correct before starting the tool.
Keep hands and fingers away from moving parts.
WARNING Risk of Injury
Make sure that the correct parameter file is being used.
Wrong parameter file might cause too high torque with
bodily injury as a result.
Compare the maximum torque which is shown in the
controller, with the maximum torque stated in the
technical data of the tool, they should be the same.
Lock-off Lever
The function of the lock-off lever is to avoid unintentional
starting of the tool.
© Atlas Copco Industrial Technique AB - 9834 5905 00
Flip the lock-off lever trigger to lock/unlock the safety
function. Always put the lever in locked position before
putting away the tool.
• Make sure the tool is equipped with a lock-off lever.
• Make sure that the lock-off lever works correctly.
• Replace the lock-off lever if it does not work correctly.
• Never remove the lock-off lever or lock it with tape.
Illustration 1: Locked position.
Illustration 2: Unlocked position.
Service and Maintenance
General Service and Maintenance Safety
Always keep the controller switched off, and removable bat-
teries removed, during service in order to avoid unexpected
start-up.
Refer servicing to qualified personnel only.
Cleaning Instructions
Clean parts with a damp cloth. Only use water, no cleansers
containing solvents should be used.
Contact your Atlas Copco service technician for cleaning ad-
vice as per current recommendations and for your particular
tool.
Preventing ESD Problems
The components inside the product and controller are sensi-
tive to electrostatic discharge. To avoid future malfunction,
make sure that service and maintenance is carried out in an
ESD approved work environment. The figure below shows an
example of an appropriate service work station.
Safety Information
7

Werbung

loading

Diese Anleitung auch für:

8436006110