Elica Nikolatesla Unplugged PRF0184546 Montage- Und Gebrauchsanweisungen Seite 20

seconds, indicating that the procedure was carried out and
saved successfully.
USING THE EXTRACTOR
● Extractor flap:
The extractor zone is fitted with a mechanical rotating
FLAP. The FLAP must be opened before switching on
the hood to activate the extraction system. The hood
has a sensor which when the extractor is on stops the
motor automatically if the FLAP is closed. The suction
function restarts only when the FLAP is reopened.
If you attempt to activate suction with the FLAP closed, the
display (5) and the "OPEN" LED will start to flash and the
motor will remain off.
● Suction speed:
The hob features 9 suction speed levels from
a Booster level .
● Extractor activation / deactivation:
Activation:
Open the FLAP at the centre of the hob; from position zero
(1), R the HOOD knob; each click will gradually
increase the suction power.
The currently active power level will be shown on the
display (2).
Deactivation:
From any position other than zero, L
taking it back to position zero(1); the display will show
● Suction Booster:
Activation:
OWR the HOOD knob; the flashing symbol
appear on the display.
This mode uses the maximum power of the extractor, it is
timed and it lasts 5 min. An acoustic signal indicates when
this time is over, then the power automatically goes back to
level .
Deactivation:
The booster can be deactivated at any time, by turning the
knob to level .
● Automatic mode
The hood will automatically select the most suitable speed,
adapting the extraction capacity to the maximum cooking
level used in the cooking zone.
When the cooking zones are switched off, the hood adapts
its extraction speed, decreasing it gradually, to eliminate
residual vapours and odours.
Activation:
OWL
sec. The LED
will indicate the activation of this function.
Deactivation:
To deactivate this function, repeat the activation procedure.
Note:If the filter maintenance signal is present, this function
cannot be activated.
● Activation / deactivation of grease and odour filter
saturation indicator
Note: This indicator is normally deactivated.
To access the filter activation / deactivation menu:
With all displays off, OWL
in this position for 8 sec.
to plus
Note: The first setting option suggested is the GREASE
FILTERone; for this reason, display (5) will show the
symbol
the letter
and hold the position for 2 sec.
To activate / deactivate the Grease filter saturation
indicator
Go to the GREASE FILTER
HOOD knob. Each time the knob is rotated and released,
the indicator is switched on and off.
the HOOD knob,
When the indicator is active, in display (5) a dot appears
.
next to the letter, in this case
To activate / deactivate the Odour filter saturation
indicator
will
Go to the ODOUR FILTER
same operations indicated for the activation / deactivation
of the GREASE FILTER.
Selected setting confirmation:
Having defined the desired settings, OWL
knob and hold this position for 8 sec. An acoustic signal will
indicated that the settings have been saved.
● Filter saturation indicator
Note: this function is disabled by default; it is activated
when the grease and/or odour filter saturation indicators
are activated (see procedure above)
When it is time to replace the grease and/or odour filter, the
following symbols will appear on the display (5):
Odour filter:
20
the HOOD knob and keep it in this position for 1
(6) will light up and an acoustic signal
; to switch to the ODOUR FILTER setting, OWL
and hold the position for 2 sec. Display (5) will show
. To go back to the previous setting, OWL
:
:
Flashing for 10 sec.
the HOOD knob and stay
setting, then OWL the
setting and perform the
the HOOD