Hama 4in1 Bedienungsanleitung Seite 2

4in1
POWER
1 17 1
2
DVD SAT
TV VCR
3 3
PROG+
4 16 4
SETUP SHIFT
OK
5 15 5
14
PROG-
MENU EPG EXIT
6 13 6
7 12 7
1 2 3
4 5 6
8 8
7 8 9
0
AV -/--
9 11 9
10 10
Art.Nr.: 00011412
g Operating Instruction
8in1
Universal Remote Control
Thank you for your decision for a Hama product.
Take your time and read the following instructions
and information completely. Please keep these
POWER
MODE instructions in a safe place for future reference.
17
M
Function buttons (Models 4 in 1, 8 in 1)
DVBT CBL
AUX AMP
DVD SAT
TV VCR
1. LED indicator
PROG+
2. Mode key for selection of secondary device
16
group (only 8 in 1 model: AUX,DVBT,CBL,AMP)
SETUP SHIFT
3. Device selection keys
OK
4. Setup: Remote control settings
15
5. Vol+/Vol-: Volume control
6. Text ON: Switch on Teletext
Menu: Open device menu
14
7. Hold: Hold the current Teletext page
PROG-
8. Number Keys 0-9
MENU EPG EXIT
13
9. AV: selects external A/V sources
10. ◄◄ Rewind/red
12
► Play/yellow
1 2 3
►► Fast forward/blue
● Start recording
■ Stop/green
4 5 6
ll Pause/magenta
11. -/- -: Switch to two-digit channel numbers
12. Info: On-Screen information (if supported by
7 8 9
A/V device)
EPG: Electronic Programme Guide (if supported
0
AV -/-- by selected A/V device)
11
13. Text OFF: exits Teletext
EXIT: exits device menu
14. PROG+/PROG-:Programme selection up/down
15. Mute Switch
OK: Confirms a selection
16. Shift key
17. Power: ON/OFF
1. Explanation of the Note symbol
Note
► This symbol is used to indicate additional in-
Art.Nr.: 00011413
formation or important notes.
2
2. Package Contents
- Universal Remote Control (URC)
- Code List
► The remote control switches off automatical-
- This operating instructions
3. Safety notes
• Do not use the Universal Remote Control in mo-
ist or wet environments and avoid spray-water
contact.
• Do not expose the Universal Remote Control to
heat sources or direct sunlight.
• Do not drop the Universal Remote Control..
5. Setup
• Never open the Universal Remote Control. It
contains no user-serviceable parts.
• As with all electrical devices, keep the Universal
Remote Control away from children.
► To obtain a proper infrared (IR) transmission,
4. Getting started – installing the Batteries
Note
► Press the "MODE" key to select the seconda-
► Alkaline batteries are recommended. Use 2
„AAA" (LR 03/Micro) type batteries.
► Remove the battery compartment lid on the
► Press the Shift key to operate the blue func-
back of your URC.
► Check the required battery polarity and in-
sert batteries according to the "+/–" marks
inside the compartment.
► No entry for approx. 30 seconds will time out
► Close battery compartment lid.
Note: Code saver
► Each device type can be programmed under
► Any codes you have programmed remain
stored for up to 10 minutes while you re-
place the battery .Make sure you do not ► If you want to control a device , it´s not pos-
press any buttons before you have placed
new batteries inside the remote control.
All the codes will be erased if a button is
pressed while there are no batteries in the
remote control.
5.1 Direct Code Entry
Note: Battery saving function
Your Universal Remote Control Package contains a
code list. The code list shows 4-digit codes for most
A/V device manufacturers in alphabetical order and
ly when a button is pressed down for more
grouped by device type (e.g. TV, DVD, etc.). If the
than 15 seconds. This conserves battery
device you want to control is covered by the code
power if the remote control gets stuck in a list, the Direct Code Entry is the most convenient
entry method.
position where the buttons are continually
pressed down,such as between sofa cushi-
5.1.1 Turn on the device you want to control
ons.
5.1.2 Press the SETUP key until the LED indicator is
permanently lit.
5.1.3 Select the device you want to control using
the device key (e.g. TV). A successful selection
is indicated by the LED with one flash follo-
Notes
wed by permanent light.
5.1.4 Check code list for brand and type of the
device you want to control.
allways point your Remote control in the ap- 5.1.5 Enter the corresponding 4-digit code using
the 0 – 9 keys. The LED indicator confirms
proximate direction of the device you want
each entered digit via a short flash and turns
to control.
off after the fourth digit.
ry device group :AUX, AMP, DVB-T, CBL (only
Note
8 in1 Model).
► If the code is valid, it is saved automatically
tion keys. The Shift function deactivates by
► If code is invalid, the LED indicator flashes
pressing the Shift key again, or automatically
six times and then turns off. Repeat steps
after approx. 30 sec. without use.
5.1.1 to 5.1.5 or use a different code entry
method.
the Setup mode. The LED indicator shows six
flashes and turns off.
5.2 Manual code search
Your Universal Remote Control is equipped with
an internal memory, which is preloaded with up to
any device key, i.e a TV can be programmed
350 codes per device type for the most common
under DVD, AUX, etc.
A/V devices. You can zap through these codes until
the device you want to control shows a reaction.
sible while the Universal Remote Control is
This might be that the device you want to control
in the Setup Mode. Exit the Setup mode and
switches off (POWER key) or changes the channel
select the device you want to control using (PROG+/PROG- keys).
the device selection keys.
5.2.1 Turn on the device you want to control
5.2.2 Press the SETUP key until the LED indicator is
permanently lit.
3