Royal Catering RCFZ-459+ Bedienungsanleitung Seite 6

E C
H
I
F
S
A. cover
B. cover gasket
C. internal lighting
D. housing
E. chamber for frozen products
F. ventilation grid
G. control panel
H. parting
I. chamber for products intended for freezing
K. hanging basket
L. compressor chamber
M. compressor
N. desiccant filter
O. fan
P. capillary tube
S. water drain
3.2. PREPARING FOR USE
GENERAL HINTS FOR THE USER
The appliance must be cleaned after unpacking and before
its connection to the power supply network. Once the
freezer has reached the set temperature, it can be filled
with. It is forbidden to fill the freezer with warm liquids and
food and any food products put into the appliance should
be covered. Food products and drinks should be stored
in sealed airtight containers. In order to ensure adequate
air circulation inside the appliance it is recommended to
place products be in such a manner in order to maintain
distance between them. If the door is opened too often,
there is increased energy consumption, which could
lead to possible damage. Always close the door of the
appliance when it is not in use. Do not use screwdrivers
or other metal tools in order to remove ice layers that
are formed on the walls of the appliance during its use.
After closing the cover, do not open it again suddenly and
with use of force, the gasket located around the closure
of the appliance chamber can hinder to open it for about
1 or 2 minutes. After this time, the appliance should open
normally. In case of you do not use the appliance for
a longer time, in order to save electricity, it is necessary
to disconnect the cleaned appliance from the electricity,
to clean and leave the door open in order to prevent
gathering of unpleasant odours inside the appliance.
APPLIANCE LOCATION
Make sure that the device stands in a vertical position for at
least 2 hours before it is switched on, in order for the refrigerant
circuit to stabilize (otherwise technical failure may occur).
CAUTION! Correct connection of the device to the single
socket with earth is the guarantee of proper work. In the
case of inappropriate installation, the machine may cause
injury. Place the appliance on a flat, stable surface that will
withstand its weight together with its contents. In order
to provide adequate ventilation, keep at least 20 cm of
space between the appliance and the wall or other objects.
10
The device should be placed in a cool, well-ventilated
and dry room, away from heat sources. Ensure at least
30 cm clearance from gas or electric cookers and 50
cm distance from radiators or ovens. Not exposing the
device to heat sources during its operation increases the
compressor efficiency and reduces energy consumption.
First start up
K
1. Unpack the whole appliance.
2. Make sure that no packing material has been left in
the compressor chamber.
3. Remove all documents and other accessories from
the inside of the appliance.
4. Install all additional components of the appliance.
5. Level the appliance.
6. Clean and dry the interior.
7. Close the cover / door of the appliance.
8. Connect the appliance plug to the socket.
9. Set the cooling power to the maximum.
10. Do not open the device for approximately 4 hours.
11. Insert frozen products into the freezer
12. Do not store any glass bottles with liquids, because
they increase their volume during freezing and may
be damaged. Never store explosive substances in the
freezer.
Height adjustment / levelling:
In order to adjust the height or level of the freezer, it is
necessary to unscrew or screw in the feet of the appliance.
Assembly of the lock:
1. Remove the tape covering the screw holes for the
catch.
2. Position the catch in the correct mounting position.
3. Screw the catch with two screws.
The handle assembly:
1. Fix the handle on the door with 4 screws.
2. Insert the handle cover beginning from one side and
ending on the other side.
3. Push the cover into the holder.
The appliance is equipped with a lock which enables to
protect the freezer against opening.
Rev. 11.04.2019
3.3. DEVICE USE
CONTROL PANEL
B
A C
ADJUST SET
A. The button activating control in a selected mode
B. Display
C. Mode and value change button
Push and hold button C for 3 seconds. Pushing and
releasing the button display available device setting
modes: F1, F2, F3, F4, F5
• F1 – Cooling temperature. When the display shows
F1, press the button A and then set the temperature
using the button C.
• F2 – Temperature difference (range 1 to 5). It allows
setting the tolerance for the difference between the
temperature which has been set and the current
temperature inside the device. For example, when
the temperature inside the device is set to-18°C,
setting F2 to 3 causes the compressor to stop at-
18°C and then to restart at-15°C.
• F3 – Temperature calibration (range-5 to +5). If
the set temperature is, for example,-18°C and the
calibration setting is +2, then the display shows
temperatures from-18°C to-16°C.
• F4 – Defrosting cycle (from 0 to 6 hours). If set to
3 hours, the device will defrost every 3 hours (the
compressor stops).
• F5 – Defrosting time (from 0 to 20 min). If set to 10
minutes, each defrosting cycle lasts 10 minutes (the
compressor will not run for 10 minutes).
The temperature should be set depending on:
• ambient temperature
• quantity of stored food
• opening frequency
To obtain the lowest possible cooling temperature, the
ambient temperature should be around 25°C.
FREEZING OF FRESH FOOD
1. Place the packaged fresh food in the freezer, paying
attention so that it will not come in direct contact with
already frozen products because they may defrost
and shorten their shelf-life. It is recommended that
fresh food will be placed near the wall or bottom of
the freezer, in these places it is the coldest.
Do not exceed the allowed freezer food quantity for
a given appliance (X kg / 24h). Check this value in the
technical data of the appliance or on the rating plate.
2. Set the cooling power to the maximum.
3. After 24 hours it is necessary to change the location
of the frozen food so that it will be possible to freeze
other products.
4. Set the cooling power which will be appropriate for
filling of the freezer.
MAXIMUM FILLING HEIGHT OF THE FREEZER
Never fill the freezer until the edge being in contact with
the cover. Always keep the distance between the cover and
the frozen products. Set the temperature adjustment knob
depending on the filling of the freezer.
Rev. 11.04.2019
DEFROSTING
Under normal conditions of use (3-4 openings per day), the
freezer should be defrosted once or twice a year (in case
of more frequent opening the freezer should be defrosted
more often). The appliance must be defrosted especially
when the thickness of the ice layer on its walls will be about
5-7 mm. Ice layers on the internal walls of the appliance
reduce its efficiency. Layers of ice can be scraped with
a plastic scraper. Do not use metal things to scrap ice from
the appliance. Warning! Never use electrical appliances
to defrost freezers (e.g. hair dryer) or open flames (e.g.
candles). The plastic parts of the interior can melt and the
emanate vapours can inflame through sparks or a flame.
In order to defrost it is necessary to proceed as follows:
1. Make sure the appliance plug is removed from the
socket.
2. It is recommended to use a plastic bowl or other
sealed container to collect leaking water in the
course of defrosting.
3. Make sure that the hands are dry in the course of
performing subsequent activities in order to avoid
damages caused by a negative temperature (use of
gloves is recommended).
4. Remove the frozen products and make sure that the
water melting from them will not cause any danger
or damages. It is recommended to place them in
a sealed container.
5. Using a flat tool, lever up and remove the stopper
from the bottom of the freezer.
6. Pull out manually the plug located in the front
bottom part of the freezer, provide a suitable
container for the water flowing out.
7. It is recommended to scrape the thickest layers of ice.
8. If necessary, defrosting can be accelerated by
inserting a dish with warm water dish (not boiling or
hot!) into the freezer.
9. Wait until the ice from the inside of the freezer is
melted, in the course of defrosting it is possible to
remove the water from the inside of the freezer with
a sponge.
10. Before using the appliance again, clean the inside of
the appliance.
11. Plug the holes (on the bottom of the freezer and in
its front bottom part) with stoppers.
12. Close the cover / door and connect the appliance to
the power supply. 13. Set the cooling power to the
maximum.
14. Insert products to be frozen into the freezer.
15. After about 4 hours, set the cooling power to match
the amount of produce in the freezer.
INTERIOR LIGHTING
When the freezer cover is open, the internal lighting of the
appliance automatically lights up automatically. When the
freezer cover is closed, the interior lighting of the appliance
goes out.
INTERNAL BULB REPLACEMENT
Replacing or repairing the bulb should be done by qualified
staff. Before bulb replacement or any other maintenance
work, remove the plug from the socket. The light bulb
is located behind the transparent cover on the door of
the device. If you need to replace the bulb, unscrew and
remove the cover, replace the light bulb making sure the
parameters of the new one are the same, and screw the
cover back on.
11