Werbung
Verfügbare Sprachen
Verfügbare Sprachen
9.
Before commissioning
In accordance with the applicable regulations, the
high-pressure cleaner must never be operated in the
drinking water network without a system separator.
A suitable system separator in accordance with EN
12729 type BA must be used.
Water that has flowed through a system separator
backflow prevention device is considered non-potable.
A system separator is available from specialist dealers.
A system separator (backflow preventer) prevents
water and cleaning agent from flowing back into the
drinking water pipe.
• Use a standard 1/2" garden hose with at least 5 m
length for the water inlet. Do not exceed 30 m length.
• Use the product with a domestic water connection
with at least 500 l/h flow rate.
• You can also use the product independently of
the water supply (e.g. rain barrel) thanks to the
integrated water suction function. This function can
only be used with a suction hose with filter basket.
A suction hose with filter basket is not included in
the scope of delivery.
10. Assembly (Fig. 1 + 2)
1.
Place the product upright on a level, firm surface.
2.
Slide the bracket handle (1) onto the connection
on the top of the product and fix it with two screws
(20). Use a Phillips screwdriver for this (not
included in the scope of delivery).
3.
Attach the mounting bracket for the high-pressure
hose (8) to the back of the device with two screws
(20). Use a Phillips screwdriver for this (not
included in the scope of delivery).
4.
Plug the mounting bracket for the mains connection
cable (2) and the mounting bracket for accessories
(7) onto the two connection points on the side of
the device.
5.
Insert one of the high-pressure hose connection
coupling plugs (18) into the spray gun high-
pressure hose connection (16) and the other
coupling
plug
into
connection (6) so that they snap into place.
6.
To remove the high-pressure hose (18), operate
the locking button (17) on the spray gun (13) and
the locking button (5) on the product and pull out
the high-pressure hose (18).
24 | GB
the
high-pressure
hose
www.scheppach.com
7.
Screw the coupling for the water connection (19)
onto the water connection (9).
8.
Use a garden hose with quick coupling (not
included in the scope of delivery) and connect it to
the water connection coupling (19).
9.
Connect the lance (12) to the spray gun (13) by
plugging it in and screwing it in (bayonet catch).
10. Once the lance (12) is fitted, connect the variable
nozzle (10) to the lance (12). To do this, insert the
variable nozzle (10) into the lance (12) so that it
locks into place. To remove the variable nozzle
(10), press the nozzle release button (11) on the
front end of the lance (12) and pull the attachment
off towards the front.
11. Starting operation (Fig. 1 + 2)
m Attention!
Always make sure the product is fully assembled
before commissioning!
Selecting attachments
Choose a suitable attachment depending on the work
you need to do:
Variable nozzle (6): The variable nozzle (10) with
its flat jet is particularly suitable for surface cleaning.
You can adjust the width of the water jet by turning the
nozzle tip.
11.1 Switching on
m WARNING! Pay attention to the recoil force
caused by the emergent water jet. Ensure that
you have secure footing and hold the spray gun
(13) firmly. Otherwise, you could injure yourself or
others.
m WARNING! If there are leaks in the water system,
switch off the product immediately with the On/Off
switch (3) and disconnect the product from the
mains with the mains connection cable. There is
a risk of electric shock! Start connecting the water
connections again.
NOTE: Do not operate the product with a closed water
tap. Running dry will damage the product.
1.
Ensure that the high-pressure cleaner is switched
off at the On/Off switch (3).
2.
Plug the mains plug into the socket.
3.
Open the water tap fully.
Werbung
