Dometic MB 3000 G Installation, Bedienung Und Wartung Seite 10

• P P o o w w e e r r f f a a i i l l u u r r e e a a l l a a r r m m
• The
• The audible alarm sounds.
• C C L L E E A A N N
This indicates that the cleaning interval has been exceeded, that is to say, the condenser must be cleaned
(see the section "Periodic Maintence"). The message disappears and the audible signal is muted when the
key is pressed.
• The audible signal can be muted for a certain period of time by pressing the
alarm situation persists beyond this time, the audible alarm comes back on.
• In both these situations, you must try to discover the cause of the alarm and eliminate it as quickly as pos-
sible. If this is not successful, you must immediately take the necessary action to ensure that the goods being
stored are not harmed.
ERROR MESSAGES
• As well as alarm situations, the unit also indicates functional errors. If there is a functional error, an audible
signal sounds and a relevant message is displayed. (The messages displayed depend on the language that
has been set - see the table below.)
• The audible signal can be muted for a certain period of time by pressing the
error persists beyond this time, the audible alarm comes back on.
• When an error occurs, the necessary action must be taken immediately to ensure that the goods being sto-
red are not harmed. You must inform your local service centre immediately, telling them not only the error
message, but also the essential product number and serial number of the unit.
• The electronics may display the following errors:
C C O O M M P P
Compressor malfunction
B B A A T T L L O O W W Battery voltage too weak
B B A A T T F F A A I I L L Battery fully discharged, not connected or defective
R R E E G G U U S S E E N N Defective control sensor or a fault in the connecting lead
M M I I D D S S E E N N
Defective temperature sensor or a fault in the connecting lead
P P R R G G M M E E R R R R Configuration parameters and board settings do not match
T T E E S S T T E E R R R R Error during the self-test phase
Translation table for warning and error messages (dependent on LAN parameter)
E E N N G G E E S S P P P P O O R R
CLEAN LIMP LIMP
COMP COMPRES COMPR
BAT LOW BAT BAJA BAT BAIX
BAT FAIL AVER BAT AVA BAT
REGU SEN SEN REG SEN REG
MID SEN SEN MED SEN MED
PRGM ERR PRGM ERR PRGM ERR
TEST ERR TEST ERR TEST ERR
(also refer to "Power Failure" section)
LED flashes
F F R R A A D D E E U U B B H H M M
NETT REIN BERSIH
COMP KOMP IPAS
BAT FAIB BAT SCHW BAT REN
PAN BAT BAT AUSF BAT ROSA
REGU SON REGS AUS SEN REGU
SOND CEN SO-M AUS SEN TENG
PRGM ERR PRGM ERR PRGM ERR
TEST ERR TEST ERR TEST ERR
N N E E D D S S V V E E S S U U O O
REINIGEN RENG PUHDISTA
COMP KOMP KOMPR
BAT ZWAK BAT LAG AKKUJAN
BAT LEEG BAT FEL AKKUVIKA
REG SEN REGL GIV OHJ ANT
MID SEN MED GIV LAMP ANT
PRGM ERR PRGM ERR PRGM ERR
TEST ERR TEST ERR TEST ERR
10
key (MUD parameter). If the
key (MUD parameter). If the
N N O O R R I I T T A A D D A A N N
REN PULIZIA RENS
KOMPRES COMP KOMP
BAT LAV BAT BAS LAVT BAT
BAT FEIL AVAR BAT BATFEJL
TRYKK REG SEN TRYK KON
MID SEN SEN MED MID SEN
PRGM ERR PRGM ERR PRGM ERR
TEST ERR TEST ERR TEST ERR