Seite 1
Controls 3.0 Zentrales Lüftungsgerät Central ventilation unit Unité de ventilation centrale KWL 250 W KWL 250 W ET Kompaktes Wandgerät mit Wärmerückgewinnung und EC-Technik Compact wall-mounted unit with heat recovery and EC technology Centrale murale compacte avec récupération de chaleur...
Seite 2
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET INHALTSVERZEICHNIS MONTAGE- UND BETRIEBSVORSCHRIFT KAPITEL 1 SICHERHEIT ................................. SEITE 3 Grundlegende Hinweise ................................. Seite 3 Warnhinweise ..................................Seite 3 Sicherheitshinweise ................................Seite 3 Einsatzbereich ..................................Seite 4 Personalqualifikation ................................Seite 4 KAPITEL 2 GRUNDLEGENDE HINWEISE ............................
Seite 3
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET DEUTSCH KAPITEL 8 SOFTWARE easyControls 3.0............................ SEITE 23 Menüübersicht ..................................Seite 23 Startseite ....................................Seite 23 8.2.1 Lüftungsprofile ................................... Seite 23 8.2.2 Filterwechsel ..................................Seite 23 8.2.3 Temperaturen ..................................Seite 24 8.2.4...
Seite 4
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 1 Grundlegende Hinweise Zur Sicherstellung einer einwandfreien Funktion und zur eigenen Sicherheit sind alle nachstehenden Vorschriften genau SICHERHEIT durchzulesen und zu beachten. Die national einschlägigen Normen, Sicherheitsbestimmungen und Vorschriften (z.B.
Seite 5
Einsatzbereich – Bestimmungsgemäßer Einsatz Das zentrale Lüftungsgerät KWL 250 W/W ET mit Wärmerückgewinnung, ist für die zentrale Be- und Entlüftung von Wohnhäusern und Etagenwohnungen konzipiert. Das Gerät ist zur Förderung normaler oder leicht staubhaltiger (Parti- kelgröße < 10 µm), wenig aggressiver und feuchter Luft, in gemäßigtem Klima und im Bereich seiner Leistungskennlinie geeignet.
Seite 6
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 2 Transport Das Gerät ist werkseitig so verpackt, dass es gegen normale Transportbelastungen geschützt ist. Der Transport muss GRUNDLEGENDE sorgfältig durchgeführt werden. HINWEISE Bei Weiterversand, vor allem über längere Distanzen (z.B. Seeweg) ist zu prüfen, ob die Verpackung für Transportart und -weg geeignet ist.
Seite 7
Alle Ausführungen der zum Gerät gehörenden Dokumentationen müssen beachtet werden, sonst entfällt die Gewähr- leistung. Gleiches gilt für Haftungsansprüche an den Hersteller. Der Gebrauch von Zubehörteilen, die nicht von Helios empfohlen oder angeboten werden, ist nicht zulässig. Even tuell auftretende Schäden unterliegen nicht der Gewährleistung.
Seite 8
Der Wärmebereitstellungsgrad ist von den Faktoren Luftfeuchtigkeit und dem Temperaturunterschied zwischen Außen- und Abluft abhängig. Geräte mit Enthalpie-Wärmetauscher (KWL 250 W ET) gewinnen neben der Wärme auch Feuch- tigkeit aus der Abluft zurück, die den Räumen mit der Zuluft wieder zugeführt wird.
Seite 9
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Bei Verwendung eines Heizregisters, muss das Rohrsystem 0,5 m vor und nach dem Heizregister mit temperaturbeständigem bzw. nicht brennbarem Rohr versehen werden (z.B. Wickelfalzrohr) Abb. 2 Abluft Abb. KWL 250 W Zuluft ...
Seite 10
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Abmessungen Abb. 3 133 192 157 Abluft Fortluft ø125 Zuluft Außenluft Kugelsiphon ø12 ø125 Zuluft Maße in mm Zubehör Zur Erweiterung des KWL Systems stehen weiteres Zubehör sowie passende Systemkomponenten zur Verfügung.
Seite 11
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 4 Einbauhinweise 4.1.1 Positionierung MONTAGE Das Gerät ist zur Installation innerhalb der Wohneinheit bzw. des Gebäudes, an der Wand oder zum Einbau in einen Schrank, vorgesehen. Aufgrund der Betriebsgeräusche wird empfohlen, das Gerät in einem Nebenraum (z.B. Wasch- raum, Technikraum oder Abstellraum) zu installieren.
Seite 12
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Für den Umbau des Gerätes wie folgt vorgehen: Verletzungsgefahr durch Herunterfallen der Gerätetür bzw. -rückwand sowie des Wärmetauschers! WARNUNG Die Gerätetür bzw. -rückwand sowie der Wärmetauscher können beim Entfernen herunterfallen und schwere Ver- letzungen verursachen.
Seite 13
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Kugelsiphon montieren Während der Heizperiode kann es durch den Prozess der Wärmerückgewinnung, im Wärmetauscher zur Bildung von Kondensat kommen. Das Kondensat muss frei aus dem Gerät ablaufen können. Hierzu muss der beiliegende Kugelsi- phon (Lieferumfang) in der Bodenwanne des Gerätes montiert werden.
Seite 14
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET 6. Kondensatschlauch (Länge max. 1,5 m) an das Entwässerungssystem des Gebäudes anschließen (s. Abb. 17). Abb. 17 Kondensatschlauch DN 12 mm (Gefälle beachten!) 7. Kugelsiphon kontrollieren: – Um die Dichtheit zu gewährleisten, darf der Kugelsiphon bei bauseitiger Montage keinen seitlichen Belastungen durch den Kondensatschlauch ausgesetzt sein! –...
Seite 15
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET 5.1.1 Anschlussplan Abb. 18 Modbus Leitungslänge: maximal 100 m es müssen paarw eise verdrillte Aderpaare verw endet KWL-KNX KWL-EM eC w erden. Connect Art. Nr.: 40155 Art. Nr. 20253 3x0,5 mm...
Seite 17
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 6 Erstinbetriebnahme Für die Erstinbetriebnahme muss das Gerät ordnungsgemäß an das Stromnetz angeschlossen bzw. mit dem Stromnetz INBETRIEBNAHME verbunden sein. Anschließend kann der Inbetriebnahmeassistent über den lokalen Webserver oder optional über das Bedienelement KWL-BE Touch (Zubehör) durchgeführt werden.
Seite 18
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET > Die Einstellungen für die Konfiguration des Gerätes werden angezeigt. Abb. 22 4. Gerät konfigurieren und auf „Weiter“ klicken. > Die Zusammenfassung der Einstellungen öffnet sich. 5. Einstellungen prüfen und ggf. anpassen.
Seite 19
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Abb. 23 Abb. 24 Kennlinie KWL 250 W Kennlinie KWL 250 W ET Zu- und Abluft Zu- und Abluft 10 % â â 10 % â â 20 % 20 % ê...
Seite 20
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET 5. Die ermittelten Differenzdrücke der Ab- und Fortluftmessung in die Kennlinie des Gerätes für Abluft (s. Abb. 23 bzw. Abb. 24), entsprechend der im Lüftungsprofil hinterlegten Ventilatorleistungen, eintragen (vgl. Abb. 26 und Abb. 27).
Seite 21
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET ⓘ Wir empfehlen folgende Werte in den Lüftungsprofilen zu hinterlegen: • Reduzierte Lüftung ≙ Lüftungsprofil „Unterwegs“ • Nennlüftung ≙ Lüftungsprofil „Zuhause“ • Intensivlüftung ≙ Lüftungsprofil „Intensivlüftung“ Gesamt-Luftvolumenströme durch ventilatorgestützte Lüftung nach DIN 1946-6:2019-12 Lüftung zum...
Seite 22
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET 5. Unter „Ventilatoreinstellung“ die Ventilatorleistungen für Zu- und Abluft gemäß der ermittelten Werte für die Nenn- lüftung eintragen (vgl. Abb. 31). Abb. 31 6.3.3 Volumenstrommessung zur Einregulierung der Anlage (Feinjustierung) durchführen •...
Seite 23
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 7 Lokaler Webserver Das Gerät kann über den lokalen Webserver mittels einem Webbrowser, über ein mobiles Endgerät (z.B. Notebook, PC, BEDIEN- Tablet, Smartphone) konfiguriert werden. Es ist keine Anmeldung/Registrierung des Gerätes erforderlich.
Seite 24
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 8 Menüübersicht easyControls 3.0 ist die Software für eine smarte und komfortable Bedienung der KWL Geräte über ein mobiles End- ® SOFTWARE gerät. Es können Einstellungen zu den folgenden Bereichen vorgenommen werden: easyControls 3.0...
Seite 25
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET • Wechselintervall Zeigt das Intervall für den Filterwechsel an. Das Intervall für den Filterwechsel ist je nach Verschmutzungsgrad ein- stellbar zwischen 1 und 12 Monaten. ⓘ Die Filter sind je nach Bedarf jedoch mind. 1x jährlich zu wechseln (Werkseinstellung: 6 Monate).
Seite 26
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Service Menü 8.4.1 Temperaturen Es werden die aktuellen Temperaturen angezeigt: • Zuluft • Fortluft • Außenluft • Abluft 8.4.2 Eigendiagnose ⓘ Die Eigendiagnose kann bis zu 20 Minuten dauern. Zur Durchführung der Eigendiagnose muss das Gerät länger als 15 Minuten eingeschaltet sein.
Seite 27
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Konfiguration 8.6.1 Ventilatoreneinstellung Ventilatorleistung für Zu- und Abluftventilator einstellen. • Zuluft • Abluft ⓘ Die Ventilatorleistungen dürfen nur bei der Einregulierung geändert werden! 8.6.2 Sensoreneinstellungen Parameter der angeschlossenen Sensoren einstellen: •...
Seite 28
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET 8.6.6 Relais Einstellungen Relais-Funktion auswählen und einstellen: • Wartungsanzeige Filterwechsel wird angezeigt (Relais-Status: geschlossen) • Fehlermeldung Fehlermeldung wird angezeigt (Relais-Status: geschlossen). Der Fehler wird auch im Fehlerprotokoll aufgezeichnet. • Fehlermeldung oder Wartungsanzeige Filterwechsel oder Fehlermeldung wird angezeigt (Relais-Status: geschlossen) •...
Seite 29
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET • Kälterückgewinnung aktivieren/deaktivieren Durch die Aktivierung der Kälterückgewinnung werden die Wohnräume mit möglichst kühler Zuluft belüftet. Die Funktion des Bypasses hängt dabei vom Temperaturniveau der Außenluft im Verhältnis zur Raumtemperatur ab.
Seite 30
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET KAPITEL 9 Gerät warten Das Gerät ist je nach Bedarf, jedoch mindestens einmal im Jahr auf Verschmutzungen und Verunreinigungen zu prüfen WARTUNG UND (Sichtprüfung). SERVICE Lebensgefahr durch elektrischen Schlag! Ein elektrischer Schlag kann zu Tod oder schweren Verletzungen führen.
Seite 31
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Wärmetauscher warten und reinigen 9.3.1 Wärmetauscher warten Der Wärmetauscher ist je nach Bedarf oder mindestens einmal jährlich auf Verunreinigungen und Verschmutzungen zu prüfen (Sichtprüfung) und ggf. zu reinigen, s. Kapitel „9.3.2 Wärmetauscher reinigen“ auf Seite 30.
Seite 32
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET Verbrennungsgefahr durch heiße Oberflächen! WARNUNG Heiße Oberflächen können schweren Verbrennungen verursachen. > Gerät 5 Minuten abkühlen lassen bzw. warten, bis die Ventilatoren ausgedreht sind. Verletzungsgefahr durch rotierende Ventilatoren! WARNUNG Rotierende Ventilatoren können Gliedmaße verletzen und schwere Verletzungen verursachen.
Seite 33
Montage- und Betriebsvorschrift Zentrales Lüftungsgerät – KWL 250 W/W ET...
Seite 34
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET TABLE OF CONTENTS INSTALLATION AND OPERATING INSTRUCTIONS CHAPTER 1 SAFETY ..................................PAGE 3 Basic information ..................................Page 3 Warning instructions ................................Page 3 Safety instructions .................................. Page 3 Area of application ..................................
Seite 35
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET ENGLISH CHAPTER 8 SOFTWARE easyControls 3.0........................... PAGE 23 Menu overview ..................................Page 23 Homepage .................................... Page 23 8.2.1 Ventilation profiles ................................Page 23 8.2.2 Filter replacement ................................Page 23 8.2.3...
Seite 36
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 1 Basic information In order to ensure correct operation and for your own safety, please read and observe the following instructions carefully SAFETY before proceeding. Relevant national standards, safety regulations and provisions (e.g. DIN EN VDE 0100) as well as the technical connection conditions of the energy supply company must be observed and applied.
Seite 37
– Intended use The central ventilation unit KWL 250 W/W ET with heat recovery is designed for the central supply and extract venti- lation of residential houses and apartments. The unit is suitable for conveying normal or slightly dusty (particle size <...
Seite 38
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 2 Shipping The delivery is packed ex works in such a way that it is protected against normal transport strain. The shipping must BASIC be carried out carefully.
Seite 39
All versions of this documentation must be observed, otherwise the warranty shall cease to apply. The same applies to liability claims against the manufacturer. The use of accessory parts which are not recommended or offered by Helios is not permitted. Any possible damages are not covered by the warranty.
Seite 40
The heat recovery efficiency depends on the factors of humidity and the temperature difference between intake and extract air. Units with enthalpy heat exchangers (KWL 250 W ET) recover humidity from the extract air in addition to heat, which is returned to the rooms through the supply air.
Seite 41
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Bei Verwendung eines Heizregisters, muss das Rohrsystem 0,5 m vor und nach dem Heizregister mit temperaturbeständigem bzw. nicht brennbarem Rohr versehen werden (z.B. Wickelfalzrohr) Fig. 2 Extract air Abluft Abb.
Seite 42
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Dimensions Fig. 3 133 192 157 Abluft Fortluft Extract air Exhaust air ø125 Supply air Zuluft Intake air Außenluft Ball siphon Kugelsiphon ø12 ø125 Supply air Zuluft Dimensions in mm...
Seite 43
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 4 Installation instructions 4.1.1 Positioning INSTALLATION The unit is designed for installation on the wall inside the residential unit or building or for installation in a cabinet. Due to the operating noise, it is recommended to install the unit in a secondary room (e.g.
Seite 44
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Proceed as follows to modify the unit: Risk of injury due to the unit door/back panel and the heat exchanger falling down! WARNING The unit door/back panel and the heat exchanger can fall down when removing and cause serious injuries.
Seite 45
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Install ball siphon During heating periods, condensate may form in the heat exchanger due to the heat recovery process. The condensa- te must be able to drain freely from the unit. The provided ball siphon (scope of delivery) must be installed in the base tray of the unit for this purpose.
Seite 46
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET 6. Connect condensate hose (length max. 1.5 m) to the building drainage system (see Fig. 17). Fig. 17 Condensate hose DN 12 mm (note gradient!) 7. The ball siphon must be inspected: –...
Seite 47
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET 5.1.1 Connection diagram Fig. 18 Modbus cable length: maximum 100 m KWL-KNX tw isted pairs of w ires must be used. KWL-EM eC Connect art. nr.: 40155 art. nr. 20253...
Seite 48
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET 5.1.2 Wiring diagram Fig. 19 MB_A MB_A MB_B MB_B +24V +24V RS_A RS_A RS_B RS_B SS-1433 +24V RS_A +24V RS_A RS_B RS_B +11V1 +24V AN/I D/I1 +24V RM/I...
Seite 49
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 6 Initial commissioning The unit must be properly connected or linked to the mains power supply for the initial commissioning. The commissio- COMMISSIONING ning assistant can then run via the local web server or optionally via the control element KWL-BE Touch (accessories).
Seite 50
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET > The settings for unit configuration are displayed. Fig. 22 4. Configure unit and click “Next”. > The settings summary page will open up. 5. Check settings and adjust if necessary.
Seite 51
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Fig. 23 Fig. 24 Characteristic curve KWL 250 W Characteristic curve KWL 250 W ET Supply and extract air Supply and extract air 10 % 10 % â...
Seite 52
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET 5. Enter the determined differential pressures from the extract and exhaust air measurement in the unit characteristic curve for extract air (see Fig. 23 and Fig. 24) according to the fan powers saved in the ventilation profile (cf. Fig. 26 and Fig.
Seite 53
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET ⓘ We recommend setting the following values in the ventilation profiles: • Reduced ventilation ≙ Ventilation profile “Away from home” • Nominal ventilation ≙ Ventilation profile “At home”...
Seite 54
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET 5. Enter the fan powers for supply and extract air according to the determined values for nominal ventilation under “Fan setting” (cf. Fig. 31). Fig. 31 6.3.3 Perform flow rate measurement for adjusting the system (fine adjustment) •...
Seite 55
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 7 Local web server The unit can be configured via the local web server using a web browser, via a mobile end device (e.g. notebook, PC, OPERATING tablet, smartphone).
Seite 56
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 8 Menu overview easyControls 3.0 is the software for the smart and comfortable operation of the KWL units via a mobile end device. ® easyControls 3.0 Settings can be configured in the following areas: SOFTWARE •...
Seite 57
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET • Replacement interval Displays the interval for filter replacement. The interval for filter replacement can be adjusted between 1 and 12 months depending on the level of contamination.
Seite 58
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Service menu 8.4.1 Temperatures The current temperatures are displayed: • Supply air • Exhaust air • Intake air • Extract air 8.4.2 Self-diagnosis ⓘ The self-diagnosis can take up to 20 minutes. The unit must be activated for longer than 15 minutes to perform the self-diagnosis.
Seite 59
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Configuration 8.6.1 Fan setting Set fan power for supply and extract air fans. • Supply air • Extract air ⓘ The fan powers may only be changed during adjustment! 8.6.2 Sensor settings...
Seite 60
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET 8.6.6 Relay settings Set and edit the relay function: • Maintenance display Filter replacement is displayed (relay status: closed) • Error message Error message is displayed (relay status: closed). The error is also recorded on the error log.
Seite 61
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET • Activate/deactivate cold recovery system The living spaces are ventilated with supply air that is as cool as possible by activating the cold recovery system. The bypass function depends on the temperature level of the intake air in relation to the room temperature.
Seite 62
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET CHAPTER 9 Unit maintenance The unit must be checked for contamination and dirt (visual inspection) as needed or at least every year. SERVICE AND MAINTENANCE Danger to life due to electric shock An electric shock can result in death or serious injuries.
Seite 63
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Heat exchanger maintenance and cleaning 9.3.1 Heat exchanger maintenance The heat exchanger must be checked for contamination and dirt (visual inspection) and, if necessary, cleaned, see chapter 9.3.2 „Heat exchanger cleaning“, page 30.
Seite 64
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET Risk of injury due to rotating fans! WARNING Rotating fans can injure limbs and cause serious injuries. > Before working on the unit, wait until the fans are turned off.
Seite 65
Installation and Operating Instructions Central ventilation unit – KWL 250 W/W ET...
Seite 66
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET SOMMAIRE NOTICE DE MONTAGE ET D‘UTILISATION CHAPITRE 1 SÉCURITÉ .................................. PAGE 3 Informations générales ................................Page 3 Consignes de sécurité ................................Page 3 Consignes de sécurité ................................Page 3 Domaines d‘utilisation ................................
Seite 67
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET FRANÇAIS CHAPITRE 8 LOGICIEL EASYCONTROLS 3.0 ..........................PAGE 23 Aperçu du menu ................................... Page 23 Page d‘accueil ..................................Page 23 8.2.1 Profils de ventilation ................................Page 23 8.2.2...
Seite 68
Filet à cheveux Le filet à cheveux empêche les longs cheveux de se coincer dans les pièces mobiles. Pour le fonctionnement, le raccordement et l’utilisation, contacter Helios en cas de doutes. Des informations supplémentaires sont consultables dans les normes et textes de loi.
Seite 69
Domaines d‘utilisation – Usage prévu La centrale KWL 250 W/W ET avec récupération de chaleur est conçue pour la ventilation centrale des bâtiments résidentiels et des appartements. L‘appareil est adapté au transport d‘air normal ou légèrement pollué (taille des parti- cules <...
Seite 70
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET CHAPITRE 2 Transport L’appareil est emballé en usine et est protégé des dégâts de transport courants. Transporter l’appareil avec précautions. INFORMATIONS En cas de transport ultérieur, en particulier sur de longues distances (par exemple par mer), il faut vérifier si l‘emballage GÉNÉRALES...
Seite 71
Si toutes les consignes indiquées dans cette notice ne sont pas correctement respectées, la garantie s’annule. Idem pour les garanties constructeur Helios. L’utilisation d’accessoires, non fournis, non conseillés ou non proposés par Helios, est interdite. Tous changements ou transformations effectués sur l’appareil sont interdits, altèrent sa conformité...
Seite 72
à l’extérieur par le conduit de rejet. Les appareils avec échangeur de chaleur à enthalpie (KWL 250 W ET) récupèrent jusqu‘à 70% d‘humidité de...
Seite 73
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET Bei Verwendung eines Heizregisters, muss das Rohrsystem 0,5 m vor und nach dem Heizregister mit temperaturbeständigem bzw. nicht brennbarem Rohr versehen werden (z.B. Wickelfalzrohr) Fig. 2...
Seite 74
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET Dimensions Fig. 3 133 192 157 Abluft air rejeté Fortluft air extrait ø125 air soufflé Zuluft Außenluft air extérieur Kugelsiphon Siphon à boule ø12 ø125 Zuluft air soufflé...
Seite 75
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET CHAPITRE 4 Instructions d‘installation 4.1.1 Positionnement MONTAGE L‘appareil est destiné à être installé au mur ou dans une armoire à l‘intérieur de l‘appartement ou du bâtiment. En raison du bruit de fonctionnement, il est recommandé...
Seite 76
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET Pour démonter l‘appareil, procéder comme suit : Risque de blessure dû à la chute de la porte ou du panneau arrière de l‘appareil ! AVERTISSEMENT La porte ou le panneau arrière de l‘appareil peuvent tomber lorsqu‘ils sont retirés et provoquer des blessures graves.
Seite 77
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET Montage du siphon à boule Pendant la période de chauffe, des condensats peuvent se former dans l‘échangeur à contre-courant en raison du processus de récupération de la chaleur. Le condensat doit pouvoir s‘écouler librement de l‘appareil. Le siphon à boule (inclus dans la livraison) doit être monté...
Seite 78
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET 6. Raccorder le tube des condensats (longueur max. 1,5 m) au système d’évacuation des eaux usées du bâtiment (à un siphon) (voir Fig. 17). Fig. 17 Tubes des condensats DN 12 mm (doit être en pente !)
Seite 79
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET 5.1.1 Schéma de raccordement Fig. 18 Longueur du câble Modbus : 100 m maximum KWL-KNX Il faut utiliser des paires de fils torsadés. KWL-EM eC Connect Numéro de poste:...
Seite 80
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET 5.1.2 Schéma de câblage Fig. 19 MB_A MB_A MB_B MB_B +24V +24V RS_A RS_A RS_B RS_B voir SS-1433 +24V RS_A +24V RS_A RS_B RS_B +11V1 +24V...
Seite 81
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET CHAPITRE 6 Première mise en service Pour la première mise en service, l‘appareil doit être correctement raccordé au réseau électrique ou branché au secteur. MISE EN SERVICE L‘assistant de mise en service peut ensuite être lancé...
Seite 82
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET > Les paramètres de configuration de l‘appareil s‘affichent. Fig. 22 4. Configurer l‘appareil et cliquer sur „Suivant“. > Le récapitulatif des paramètres s‘ouvre. 5. Vérifier les paramètres et les ajuster si nécessaire.
Seite 83
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET Fig. 23 Fig. 24 Courbe caractéristique KWL 250 W Courbe caractéristique KWL 250 W ET Air soufflé et extrait Air soufflé et extrait 10 % â...
Seite 84
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET 5. Entrer les pressions différentielles déterminées de la mesure de l‘air extrait et rejeté dans la courbe caractéristique de l‘appareil pour l‘air extrait (voir fig. 23 et 24), en fonction des performances du ventilateur enregistrées dans le profil de ventilation (voir fig.
Seite 85
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET ⓘ Nous recommandons de conserver les valeurs suivantes dans les profils de ventilation : • Ventilation réduite ≙ profil de ventilation „en déplacement“ • Ventilation nominale ≙ profil de ventilation „à la maison“...
Seite 86
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET 5. Sous „Réglage du ventilateur“, entrer les performances du ventilateur pour l‘air soufflé et extrait en fonction des valeurs déterminées pour la ventilation nominale (voir fig. 31).
Seite 87
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET CHAPITRE 7 Serveur web local L‘appareil peut être configuré via le serveur web local à l‘aide d‘un navigateur web, via un appareil mobile (par exemple COMMANDE un ordinateur portable, un PC, une tablette, un smartphone).
Seite 88
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET CHAPITRE 8 Aperçu du menu easyControls 3.0 est le logiciel pour une utilisation intelligente et pratique des appareils KWL via un appareil mobile. ® LOGICIEL Les réglages suivants peuvent être effectués : easyControls 3.0...
Seite 89
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET • Intervalle de remplacement Indique l‘intervalle de remplacement de filtre. L‘intervalle de remplacement du filtre peut être fixé entre 1 et 12 mois, en fonction du degré d‘encrassement.
Seite 90
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET Menu service 8.4.1 Températures Les températures actuelles sont affichées : • Air soufflé • Air rejeté • Air extérieur • Air extrait 8.4.2 Autodiagnostic ⓘ L‘autodiagnostic peut durer jusqu‘à 20 minutes. Pour effectuer l‘autodiagnostic, l‘appareil doit être allumé...
Seite 91
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET Configuration 8.6.1 Réglage des ventilateurs Régler la puissance du ventilateur pour l‘air soufflé et extrait. • Air soufflé • Air extrait ⓘ Les puissances du ventilateur ne peuvent être modifiées que pendant le réglage ! 8.6.2 Réglages des sondes...
Seite 92
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET 8.6.6 Réglages des relais Définir et modifier la fonction des relais : • Affichage d‘entretien Le changement de filtre est affiché (état du relais : fermé) •...
Seite 93
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET • Activer/désactiver la récupération de froid En activant la récupération de froid, les espaces de vie sont ventilés avec de l‘air soufflé le plus froid possible.
Seite 94
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET CHAPITRE 9 Entretien de l‘appareil L‘appareil doit être contrôlé en fonction des besoins, mais au moins une fois par an (inspection visuelle). ENTRETIEN ET MAINTENANCE Danger de mort par électrocution ! En choc électrique peut entraîner la mort ou des blessures graves.
Seite 95
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET Entretien et nettoyage de l‘échangeur à contre-courant 9.3.1 Entretien de l‘échangeur à contre-courant L‘échangeur à contre-courant doit être inspecté selon les besoins ou au moins une fois par an pour détecter les salissu- res et l‘encrassement (inspection visuelle) et être nettoyé...
Seite 96
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET Risque de brûlures en raison de surfaces chaudes ! AVERTISSEMENT Les surfaces chaudes peuvent causer de graves brûlures. > Laisser refroidir la centrale 5 min et attendre l’arrêt complet des ventilateurs.
Seite 97
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET...
Seite 98
Notice de montage et dutilisation Unité de ventilation centrale – KWL 250 W/W ET...
Seite 99
Notice de montage et d‘uilisation Unité de ventilation centrale – KWL 250 W/W ET...