Bosch TDS25PRO2 Gebrauchsanleitung Seite 14

en
Storing the appliance (D)
1. Always allow the appliance to cool down before
storing it.
2. Set the switches for main power and steam boiler to
the "Off/Stop" position and disconnect the connecs s
tion.
3. Place the iron on the iron pad, standing on the
soleplate.
4. Empty the water tank and store the mains cable on
the cord rewind facility. Tidy the steam hose on the
handle of the iron using the cord clip provided (14). Do
not wrap the cords too tight.
"Calc'n clean" (E)
Cleaning the Boiler
To extend the life of your steam generator and to avoid
any build up of scale, it is essential that you rinse out
the boiler after several hours of use. If the water is hard,
increase the frequency.
Approximately after 50 hours of use, "Calc´n clean" pilot
light (9) will light up indicating that boiler must be rinsed.
Do not use descaling agents for rinsing out the boiler, as
they could damage it.
1. Check that the appliance is cold and unplugged for
more than 2 hours, and that the removable water tank
(1) is empty.
2. Place your appliance on the edge of your kitchen
sink.
3. Remove the plastic cover located on the bottom of the
appliance by turning it to the
4. Unscrew the boiler drainage plug located on the
bottom of the appliance using a coin.
5. Holding your steam generator in upside down position,
and using a jug, fill the boiler (in the base unit) with 1/4
litre of water
Trouble shooting
Problem
The steam generator • There is a connection problem.
does not come on.
• The steam tank and/or main power button
is not switched on.
The iron does not • The main power button is not switched on.
heat up. • The temperature control knob is set to the
"min" position.
The iron begins • During first use: Certain components on
to smoke when the appliance have been lightly greased
switched on. at the factory and may produce a little
smoke when initially heated.
• During later use: the soleplate may be
soiled.
14
6. Shake the base unit for a few moments and then
7. Replace and tighten up the boiler drainage plug with a
8. Insert and close the plastic cover by turning it to the
To reset "Calc´n clean" pilot light and hours counter,
switch the station off twice, keeping it off during at least
30 seconds each time
Fabric protection soleplate
cover (F)
(depending on the model)
The fabricsprotection soleplate cover is used for steams
ironing delicate garments at maximum temperature
without damaging them. Use of the soleplate cover also
does away with the need for a cloth to prevent shine on
dark materials.
It is advisable to first iron a small section on the inside of
the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and pull
the elastic strap over the lower rear of the iron until it
fits tightly. To release the soleplate cover, pull the elastic
strap and remove the iron.
The fabricsprotection soleplate cover may be purchased
position.
from the customer service or specialist shops:
* Cork handle iron
Possible causes
empty it completely over a sink or bucket. To obtain
the best result, we recommend that this operation is
done twice
Important: before resclosing, make sure no water
remains in the boiler.
coin.
position.
Accessory code
(Afterssales)
464846
464745*
Solution
• Check the mains cable, the plug and the
socket.
• Press the buttons for main power (8) and
steam generator (4) "Start/I".
• Press the main power button (8) "I".
• Set the temperature control knob (15) to
the desired position.
• This is completely normal and will stop after
a short while.
• Clean the soleplate according to the
cleaning instructions in this manual.
Name of accessory
(Specialist outlets)
TDZ2510
TDZ2520*