Husqvarna 325iRJ Bedienungsanweisung Seite 18

3. Adjust the length of the harness until the suspension
point is in level with your right hip.
To start the product
1. Push and hold the start button until the green LED
comes on. (Fig. 45)
2. Use the power trigger to control the speed.
To limit the maximum speed with the
mode button
The product has a mode button. With the the mode
button the operator can limit the maximum speed. The
mode button has 3 speed levels. A lower level increases
the time of operation for the product. Use level 1 and
level 2 if the operation does not require full speed/full
power. If the operation condition requires full speed/full
power, use level 3. Do not use a higher level than
necessary for the operation.
1. Push the mode button to set a limit to the maximum
speed. The white LEDs comes on to show that the
function is on. (Fig. 46)
2. Push the mode button again to choose the next
speed level.
Automatic shutdown function
The product is equipped with a shutdown function that
deactivates the product if it is not used.
Blade thrust
A blade thrust is when the product moves to the side
quickly and with force. A blade thrust occurs when the
grass blade hits or catches on an object that cannot be
cut. A blade thrust can eject the product or operator in
all directions. There is a risk of injury to the operator and
bystanders.
The risk increases in areas where it is not easy to see
the material that should be cut.
Do not cut with the area of the blade that is shown in
grey in the illustration. The speed and movement of the
blade can cause blade thrust. The risk increases with
the thickness of the stem that is cut.
(Fig. 47)
To clear grass with a grass blade
1. Grass blades and grass cutters must not be used on
woody stems.
2. A grass blade is used for all types of tall or coarse
grass.
3. The grass is cut down with a sideways, swinging
movement, where the movement from right-to-left
is the clearing stoke and the movement from left-to-
right is the return stoke. Let the left-hand side of the
blade (between 8 and 12 o'clock) do the cutting.
18
4. If the blade is angled to the left when clearing grass,
the grass will collect in a line, which makes it easier
to collect, e.g. by raking.
5. Try to work rhythmically. Stand firmly with your feet
apart. Move forward after the return stoke and stand
firmly again.
6. Let the support cup rest lightly against the ground. It
is used to protect the blade from hitting the ground.
7. Reduce the risk of material wrapping around the
blade by always work at full speed and avoid the
previously cut material during the return stoke.
8. Stop the motor, unclip the harness and place the
machine on the ground before you start to collect the
cut material.
Grass trimming with a trimmer head
To trim the grass
1. Hold the trimmer head immediately above the
ground at an angle. (Fig. 48) Do not push the grass
trimmer line into the grass.
2. Use 80 % speed when you cut grass near objects.
(Fig. 49)
To cut the grass
1. Make sure that the grass trimmer line is parallel to
the ground when you cut. (Fig. 50)
2. Do not push the trimmer head to the ground. The
ground and the product can be damaged.
3. Do not let the trimmer head touch the ground
continuously, it can cause damage to the trimmer
head.
4. Use full speed when you move the product from side
to side to cut grass. (Fig. 51) Make sure that the
grass trimmer line is parallel to the ground.
To sweep the grass
The airflow from the rotating trimmer cord can be used
to remove cut grass from an area.
1. Hold the trimmer head and its cord parallel to the
ground and above the ground.
2. Apply full speed.
3. Move the trimmer head from side to side and sweep
the grass.
WARNING:
cover each time you assemble new trimmer
cord to prevent unbalance and vibrations in
the handles. Also do a check of the other
parts of the trimmer head and clean it if
necessary.
To stop the product
1. Release the power trigger or the power trigger
lockout.
Clean the trimmer head
1858 - 005 - 05.10.2023