Husqvarna 325iRJ Bedienungsanweisung Seite 14

equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the right
equipment.
• Use a protective helmet where there is a risk of
falling objects.
• Use approved hearing protection that provides
adequate noise reduction. Long-term exposure to
noise can result in permanent hearing impairment.
• Use approved eye protection. If you use a visor,
you must also use approved protective goggles.
Approved protective goggles must comply with the
ANSI Z87.1 standard in the USA or EN 166 in EU
countries.
• Use a visor for face protection. A visor is not enough
for protection of the eyes.
(Fig. 19)
• Use gloves when necessary, for example when you
attach, examine or clean the cutting equipment.
• Use sturdy non-slip boots.
• Use clothing made of a strong fabric. Always use
heavy, long pants and long sleeves. Do not use
loose clothing that can catch on twigs and branches.
Do not wear jewelry, short pants, sandals or go with
bare feet. Put your hair up safely above shoulder
level.
(Fig. 20)
• Keep first aid equipment close at hand.
(Fig. 21)
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
In this section the product's safety features, its purpose
and how checks and maintenance should be carried
out to ensure that it operates correctly. See instructions
Introduction on page 8 to find where
under the heading
these parts are located on your product.
The life span of the product can be reduced and the risk
of accidents can increase if product maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
WARNING:
damaged safety components. The product's
safety equipment must be inspected and
maintained as described in this section.
If your product fails any of these checks,
contact your service agent to get it repaired.
CAUTION:
on the machine requires special training.
This is especially true of the machine's
14
Read the warning
Never use a product with
All servicing and repair work
safety equipment. If your machine fails
any of the checks described below you
must contact your service agent. When
you buy any of our products we guarantee
the availability of professional repairs and
service. If the retailer who sells your
machine is not a servicing dealer, ask him
for the address of your nearest service
agent.
To do a check of the user interface
1. Press and hold the start/stop button (A).
a) The product is on when the display (B) comes
on. (Fig. 22)
b) The product is off when the display goes off.
2. If the warning indicator on the display is on or
User interface on page 20 .
flashes, refer to
To do a check of the power trigger lockout
The power trigger lockout is designed to prevent
accidental operation. When you push the power trigger
lockout forward (A) and then press the power trigger
lockout against the handle (B), the power trigger (C)
is released. When you release the handle, the power
trigger and the power trigger lockout both move back to
their original positions. This movement is operated by
three independent springs.
(Fig. 23)
1. Make sure that the power trigger is locked when the
power trigger lockout is in its original position. (Fig.
24)
2. Press the power trigger and make sure it returns to
its original position when you release it. (Fig. 25)
3. Make sure that the power trigger and the power
trigger lockout moves freely and that the return
spring operates correctly.
4. Start the product, refer to
page 18 .
5. Apply full speed.
6. Release the power trigger and make sure that the
cutting attachment stops and remains still.
To do a check of the cutting attachment guard
WARNING:
attachment without an approved and
correctly attached cutting attachment guard.
Always use the recommended cutting
attachment guard for the cutting attachment
that you use, see
If an incorrect or faulty cutting attachment
guard is attached this can cause serious
personal injury.
The cutting attachment guard stops objects that ejects in
the direction of the operator. It also prevents injuries that
occur if you touch the cutting attachment.
To start the product on
Do not use a cutting
Accessories on page 23 .
1858 - 005 - 05.10.2023