CAME RIO-CELL Bedienungsanleitung Seite 6

Tools and materials
INSTALLATION
The installer of the safety device shall provide the
end user with the following:
• safety devices must be made known to all the
appropriate people. The areas that give access to
the devices should be kept clear of obstructions
• requirements for cleaning to avoid any buildup
of hazardous material (cleaning and inspection
of IR shields).
⚠ Installation must be carried out by qualifi ed,
experienced personnel in full compliance with
applicable regulations.
Preliminary checks
-Before installing, make sure that the distance
between the RIO-CELL units is at max 10 meters
and that they are perfectly aligned, before
proceeding with the installation.
-Check that the RIO-CELL fi xing point is in a place
that is protected against shocks, that the surfaces
are solid, that there is suffi cient space to insert the
unit cover and that fi xing to the surface takes place
using suitable components (screws, anchors, etc.);
Fixing and assembly
-Prepare the holes for securing the base mount of
RIO-CELL, using the DB-L posts, the screws UNI
6954 3.9 x 32 and possible anchors for fi xing to
wall or steel surfaces.
-Fit the WL card ⓐ into the base mount of the unit.
-Insert the battery only into the WL accessory to
be stored according to the polarity indicated on
the card.
Proceed with the storage ()
-Close the device by latching the top cover and
secure it with the screws provided.
119RW4 119RW44 4 - ver. 1 1 - 10/2013
MEMORISATION
The procedure for storing WL accessories
WL is the same for all devices.
Initial conditions
RIO-CELL: insert the battery only in the card of the
WL accessory to store.
The LEDS CH1 and CH2 fl ash red; otherwise
RESET the accessory.
RIO-CONTROL:Press the [PROG] button of the card.
The BLUE WIRELESS LED remain ON.
The LEDs CH1 and CH2 on RIO-CELL go from red
to blue and start fl ashing.
RIO-CELL: press button [T1] or [T2] of the WL
accessory to memorise:
Exit
[T1]
RIO-CELL
T WL
[T2]
RIO-CELL [T1] acts on the output
R WL OUT3 of RIO-CONTROL
[T2] acts on the output
OUT4 of RIO-CONTROL
The blue WIRELESS LED of the RIO-CONTROL switch
OFF to indicate successful memorisation
☞To confi gure another RIO-CELL repeat the
accessory confi guration.
⚠Do not remove the battery in the accessory
just confi gured.
RESET PROCEDURE
-Hold down [T2] on RIO-CELL ①:
after 3 seconds the LED CH1 and CH2 switch ON
with a blue light and remain fi xed ②;
after an additional 3 seconds the CH1 and CH2
LED switch ON with a red light and remain fi xed③;
after an additional 3 seconds the CH1 and CH2
LED switch ON with a blue light and fl ash④;
☞ The LEDS CH1 and CH2 of the RIO-LUX switch
ON with a red light and fl ash⑤ to signal procedure
completion.
ACCESSORY REPLACEMENT
If replacing a RIOC-CELL reset () the entire system
(including all WL and RIO-CONTROL accessories).
Remove the battery from each WL accessory and
repeat the step for storing ().
FUNCTIONAL TESTS
After confi guring the entire, prompt manoeuvre start.
The LED of the RIO-CELL fl ash blue to indicate
that activation was successful.
Verify that the intervention of RIO-CELL establishes
Ref:
a safety condition.
❶
At the end of the manoeuvre the LEDs of the
RIO-CELL fl ash red to indicate the condition of
❷
LOW POWER (absorption reduction).
❶
⚠The LOW POWER condition maximises battery
energy saving for each WL accessory.
❷
If the LOW POWER condition is not re-engaged or
restored, set the jumper to position H of RIO-CONTROL.
ERROR MESSAGES AND WARNINGS
To know the type of error message and the warning
reported by RIO-CELL, check the points listed in the
RIO-CONTROL manual.
MAINTENANCE
Clean the protective shields using a damp cloth and
without the use of solvents.
Replacing the battery
Replace the battery when depleted.
⚠ The life of battery supplied also depends on
the storage time elapsed. Fit the batteries during
installation.
⚠ Replace with the same type or an equivalent
type of battery only.
⚠ Keep the batteries out of reach of children. If
they are swallowed, contact a doctor immediately.
Declaration - Came Cancelli Automatici S.p.A.
declares that this device complies with the es-
sential requirements and other relevant provisions
established in Directive 1999/5/EC.
Reference code for requesting a true copy: DDF
RA S002.
Decommissioning and disposal - Before pro-
ceeding, it is always advisable to check specifi c
regulations in force in the place of installation.
Packaging components (cardboard, plastic, etc.)
can be disposed of together with normal household
waste without any diffi culty, by simply separating
the diff erent types of waste and recycling them.
Other components (control boards, transmitter
batteries etc.), on the other hand, may contain
pollutants. They should therefore be removed and
handed over to companies authorised to recover
and recycle them.
DISPOSE OF PROPERLY!
The data and information provided in this manual
are subject to change at any time without prior
notice.