Herunterladen Diese Seite drucken

Kinderkraft MITZY Bedienungsanleitung Seite 19

Werbung

This product may only be used by one child at the same time
The parking device shall be engaged when placing and removing the children
The maximum basket load is 5 kg.
Maximum weight of a bag attached to the adjustable handle is 0,5 kg.
Maximum weight of cup holder: 0,5 kg.
Any additional load suspended from the buggy handles, backrest and sides will cause stability loss.
Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories.
Lift the front suspension when going up a curb or step.
Do not place the product near open flame or other heat sources.
Do not use with an additional platform.
A. Assembly
I. PUSHCHAIR COMPONENTS (FIGURE 1)
1.
Frame with seat and (2) safety harnesses
3.
Front wheels
4.
Rear wheels
5.
Guard rail
6.
Hood
7.
Cup holder
8.
Mosquito net
9.
Raincover
II. OPENING THE PUSHCHAIR FRAME
The frame should be positioned on a flat surface with the handle facing up (FIGURE A.I). To open the frame, slide the lock
(FIGURE A.II) (FIGURE A.III) on the left side of the pushchair and lift the frame up (FIGURE A.IV), until you hear the sound
of the lock. FIGURE B shows a correctly opened frame.
CAUTION! Affix the hood before using the pushchair.
III. ASSEMBLY/DISASSEMBLY OF THE WHEELS
Place the rear wheels into the opening on the rear axle until they lock completely (FIGURE C). To disassemble the rear
wheels, press the lock button on both sides of the rear axle (FIGURE D) while simultaneously pulling out the wheels from
the openings (FIGURE E). Place the front wheels in the front axle until you hear the sound of the lock (FIGURE F). To
disassemble the front wheels, press the quick-release button on both wheels (FIGURE G.I). The pushchair features a front
wheel swivel system with the option of locking to drive straight. To lock a wheel to drive straight, press the button above
the wheel (FIGURE G.II).
CAUTION! Before using the pushchair, make sure that all the
wheels have been correctly assembled.
IV. HOOD ASSEMBLY
When assembling the hood, slide the fasteners onto the frame on both sides (FIGURE H.I) until they lock (FIGURE H.II).
Next, close the zipper on both sides of the hood (FIGURE I). FIGURE J shows a correctly assembled hood. To open the
next layer of the hood, open the zipper on the hood (FIGURE K). The next layer of the hood is shown in FIGURE L.
V. ASSEMBLY/DISASSEMBLY OF THE GUARD RAIL
Place the guard rail into the appropriate openings on both sides of the frame (FIGURE M). To disassemble, press the
buttons on both sides, and remove the rail (FIGURE N).
VI. USING THE BRAKE
The pushchair is equipped with a foot-operated parking brake on the rear axle. Press the bottom part of the brake down
– once you hear the lock sound, the brake has been activated (FIGURE O). To unlock it, press the top part of the brake
(FIGURE P).
VII. ADJUSTING THE BACKREST AND FOOTREST
The seat features smooth backrest adjustment from the lie-flat position to the sitting position using the buckle (FIGURE
Q). The footrest can be adjusted to three positions. To change the position of the footrest, press the buttons on both
sides (FIGURE R). If you would like to adjust the footrest upwards, you don't need to use the buttons – simply push it
upwards.
VIII. SAFETY HARNESS
This pushchair features a safety harness suitable for newborns. Always use the fastening system. To secure your child,
slide the clasps into the central buckle until it locks (FIGURE S). Always adjust the safety harness. Press the button to
open the safety harness (FIGURE T). To assemble/disassemble, thread the shoulder, hip and crotch straps through the
openings in the seat.
IX. ASSEMBLY OF THE CUP HOLDER
Affix the cup holder to the pin on the right side of the pushchair (FIGURE U).
X. FOLDING THE PUSHCHAIR
Hold the handle and simultaneously slide the lock button (FIGURE V.I) and the folding button (FIGURE V.II), slide forward
(FIGURE W). Until the latch engages with the pin (FIGURE X).
XI. FITTING THE MOSQUITO NET
With the mosquito net hidden in the footrest, undo the zip under the footrest and put it on and secure by putting the
buttons through the loops (FIG.Y).
XII. FITTING THE RAIN COVER
The kit includes a rain cover. Attach the rain cover to the seat (FIG.Z).
XIII. CARE AND MAINTENANCE
19

Werbung

loading