janitza 800-CON Installationsanleitung Seite 7

Vorschau ausblenden Andere Handbücher für 800-CON:

Benutzerhandbuch und technische daten (58 Seiten)

Installationsanleitung (8 Seiten)

Seite von 10

/ 10
Lesezeichen

Verfügbare Sprachen

General information

Disclaimer

Compliance with the usage information for the

Safety measures

Compliance with the usage information for the

devices, modules and components is a prere-

When operating electric devices, it is unavoidable

devices, modules and components is a prere-

quisite for safe operation and attaining the

for certain parts of these devices and their com-

quisite for safe operation and attaining the

stated performance characteristics and product

ponents to conduct hazardous voltage. Conse-

stated performance characteristics and product

features. Janitza electronics GmbH assumes

quently, severe bodily injury or material damage

features. Janitza electronics GmbH assumes

no liability for bodily injury, material damage or

can occur if they are not handled properly.

no liability for bodily injury, material damage or

financial losses which result from disregard of the

• Before making connections to the device and

usage information. Make sure that your usage

its components, ground the device by means

usage information. Make sure that your usage

information is readily available and legible.

of the ground wire connection, if present.

• Hazardous voltages can be present in all

Further usage information, such as the installation

circuitry parts that are connected to the power

manual or the user manual for the basic device,

supply.

can be found on our website, www.janitza.com

• There can still be hazardous voltages present

under Support > Downloads.

in the device or the components even after

disconnection from the supply voltage (capa-

citor storage).

• Do not exceed the limit values specified in the

user manual and on the rating plate! This must

distribution or other use, in whole or in part, is

also be observed during testing and commis-

prohibited.

sioning!

• Observe the safety information and warning

notices in the usage information associated

with the device and its components!

Incoming goods inspection

The prerequisites for trouble-free and safe ope-

The scope of delivery of the 800-CON transfer

ration of the devices, modules and components

modules (set of 2) includes an input and an

include proper transport, storage, setup and

output bus connector, so that each transfer

pol-

assembly, as well as proper operation and main-

module can be used with the corresponding bus

tenance.

connector at the output or input of a series of

Exercise due caution when unpacking and

measurement devices and modules.

packing the device, do not use force and only

use suitable tools.

Check:

• Visually inspect the devices, modules and

Fig.: Output bus con-

components for flawless mechanical condition.

nector for the 800-CON

• Check the scope of delivery (see user manual)

transfer module (1 HP,

for completeness before you begin installing

see Technical data) at

your devices, modules and components.

the output of a series of

measurement devices

If it can be assumed that safe operation is no

and modules.

longer possible, take your device, module or

component out of operation immediately! Secure

against unintentional startup!

Fig.: Input bus con-

nector for the 800-CON

transfer module (1 HP)

at the input of a series

of measurement devices

and modules.

Subject to technical changes.

• Make sure that your device, module or

WARNING

component matches the installation manual.

• First make sure you have read and understood

Hazard due to disregard of warning notices and

• First make sure you have read and understood

safety information!

the usage information accompanying the

Disregard of warning notices and safety informa-

product.

tion on the device itself and in the usage informa-

• Keep the usage information associated with

tion for the device and its components can lead to

the product available for the entire service life

injuries or even death!

and pass it on to any possible subsequent

Observe the safety information and warning noti-

ces on the device itself and in the usage informa-

users.

tion associated with the devices and their compo-

• Please find out about device revisions and the

nents, such as:

associated modifications of the usage infor-

· Installation manual

mation associated with your product at

· Installation supplement

www.janitza.com.

· User manual

· Supplement Safety Information

Disposal

Please abide by national regulations! Dispose

of individual parts, as applicable, depending on

their composition and existing country-specific

regulations, e.g. as:

• Electronic waste

• Batteries and rechargeable batteries

• Plastics

• Metals

or engage a certified disposal company to handle

scrapping.

It can be assumed that safe operation is impossi-

ble if the basic device, module or component, for

ATTENTION

example:

Improper handling may cause damage to the

• Has visible damage.

module and result in material damage!

• No longer functions despite an intact power

The contacts of the bus connectors (JanBus

supply.

interface) can bend or break off and destroy the bus

• Was subjected to extended periods of unfa-

connector.

vorable conditions (e.g. storage outside of the

· Never touch or manipulate the contacts of the

bus connector!

permissible climate thresholds without adjust-

· Never force the bus connector into the module!

ment to the room climate, condensation, etc.)

· When handling, transporting and storing

or transport stress (e.g. falling from an eleva ted

the module, protect the contacts of the bus

position, even without visible external dam-

connector!

age, etc.).

INFORMATION

· Always install the 800-CON transfer module with

output bus connector at the end of your measuring

device and module topology and the 800-CON

transfer module with input bus connector at the

beginning of your remote measuring point!

· In addition to the usage information for the basic

device and the 800-CON transfer module (set of 2),

please also note any other usage information for

the modules and components integrated in your

JanBus topology.

Relevant laws,

Qualified personnel

applied standards and directives

Please see the declaration of conformity on our

To avoid bodily injury and material damage, only

Please see the declaration of conformity on our

qualified personnel with electrotechnical training

website (www.janitza.com) for the laws, stan-

are permitted to work on the device, module or

dards and directives applied for the device by

Janitza electronics GmbH.

component who have knowledge of:

Janitza electronics GmbH.

• The national accident prevention regulations.

• Safety technology standards,

INFORMATION

• Installation, commissioning and operation of

Our usage information uses the grammatical mascu-

the device and the components.

Our usage information uses the grammatical mascu-

line form in a gender-neutral sense! This form always

refers equally to women, men and diverse. In order

WARNING

to make the texts more readable, distinctions are

not made. We ask for your understanding for these

Risk of injury due to electric voltage or electric

not made. We ask for your understanding for these

simplifications.

current!

simplifications.

When handling electric currents or voltages, serious

bodily injury or death can result from:

· Touching bare or stripped leads that are energized.

· Device or module inputs that pose a hazard when

touched.

Before starting work on your system:

· Disconnect the supply of power!

· Secure it against being switched on!

· Check to be sure it is de-energized!

· Ground and short circuit!

· Cover or block off adjacent live parts!

Device short description

Mounting the module with output bus connector

The module set, consisting of 2 transfer modules,

While observing the mounting instructions for your

transmits the JanBus communication of a basic

device to remote measuring points via a data cable

basic device or the connected module (e.g. check

(for type, see technical data) (please note the

the bus connector mounting!), mount the 1st 800-

(for type, see technical data) (please note the

CON transfer module with output bus connector

specification of suitable basic devices in the

user manual). This allows you to

when the system is disconnected from the power

user manual). This allows you to

supply as follows:

implement measuring device and

module topologies with a flexible

arrangement of your DIN rails (for

DIN rail types, see Technical data)

in the control cabinet or small

distribution board.

Bottom

bolts

Fig.: Transfer modules 800-CON

(output and input)

The scope of delivery of the transfer modules

includes the appropriate bus connector (JanBus

interface).

Fig.: Module 800-CON - rear view (with output bus connector)

7 / 10

Intended use

The modules /components

• are only intended for use in industrial areas.

• are intended as an expansion or transfer mod-

ule for measurement-device and module topol-

ogies with suitable basic devices (see user

manual of the respective module) in control

cabinets and small installation distributors.

• may only be mounted with the basic device

disconnected from the power supply (see step

"Mounting"). Observe the usage information

belonging to the basic device!

The basic device and the modules are not inten-

ded for installation

• in vehicles! The use of the basic device with

modules and components in non-stationary

equipment is considered an exceptional envi-

ronmental condition and is only permitted by

separate agreement.

• in environments with harmful oils, acids, ga-

ses, vapors, dusts, radiation, etc.

• in potentially explosive environments.

INFORMATION

1. Press in the open bottom bolts on the rear of

System limits:

the module.

· For the maximum bus length (JanBus - proprietary)

2. If not already done, plug the output bus

for setting up measurement-device and module

connector (JanBus interface) included in the

topologies, refer to the "Technical data".

scope of delivery into the sockets on the back

· The transfer modules in the set can each be

used as an output or input.

of the module.

· Before installing your measuring device and module

topology, please check the number of suitable

modules and their slot assignment on the basic

device (see user manual for the respective module).

· Do not exceed the maximum number of module

slots of the basic device. The 800-CON (set of 2)

Output bus

transfer module does not occupy a slot!

connector

· Recommended data cables can be found in the

connector,

· Recommended data cables can be found in the

technical data and the user manual.

rotated

· The scope of delivery of the 800-CON module

(set of 2) can be found in the user manual for the

module.

2 2

Press the bus

connector

contacts of the

output bus

connector into

the module

sockets

janitza 800-CON Installationsanleitung Seite 7

Verfügbare Sprachen

Verwandte Anleitungen für janitza 800-CON

Verwandte Produkte für janitza 800-CON