EINHELL TC-US 380 Originalbetriebsanleitung Seite 22

•
Connect a wet and dry vacuum cleaner to
the outlet of the vacuum extractor angle (25)
(refer to the technical data for the diameter).
5.3 Adjusting the position of the grinding/
sanding belt (Fig. 10/11)
•
The grinding/sanding belt (5) can be used in
both a horizontal and a position.
•
Undo the two nuts (26) using the wrench (21).
•
Move the grinding/sanding belt (5) up.
•
Retighten the nuts (26) to secure the position.
•
In this position you can use the grinding/san-
ding table (3) to support the workpiece
•
To do so, you have to remove the stop rail (7)
(see 5.2).
•
Remove the grinding/sanding table (3) from
the mount (19) and the screw (20).
•
Fit the screw (20) to the mount (27).
•
Push the grinding/sanding table (3) into the
mount (27). Secure it by tightening the screw
(20) using the wrench (21).
•
Caution! Ensure that the distance between
the grinding/sanding table (3) and the grin-
ding/sanding belt (5) is as small as possible.
By doing this you will reduce the risk of work-
pieces getting jammed.
•
Caution! The grinding/sanding belt (5) must
be able to run freely.
•
To move the grinding/sanding belt (5) back
to the horizontal position, proceed in reverse
order. Important! Position the housing of the
grinding/sanding belt so that it rests on the
foot (28).
5.4 Changing the grinding/sanding belt
(Fig. 12/13)
•
Pull out the power plug!
•
Adjust the grinding/sanding belt (5) to the ver-
tical position (see 5.3).
•
Remove the 4 recessed head screws (29).
•
Undo the recessed head screw (30).
•
Remove the grinding/sanding belt guard (31).
•
Pull the clamping lever (10) outwards to re-
lease the grinding/sanding belt (5).
•
Remove the grinding/sanding belt (5) to the
rear.
•
Mount and the new grinding/sanding belt in
reverse order.
•
Caution! Note the running direction: Arrow
on the housing and on the inside of the grin-
ding/sanding belt!
GB
5.5 Adjusting the grinding/sanding belt
•
•
•
•
•
•
•
5.6 Replacing the abrasive paper on the grin-
Remove the front cover (16) by removing the
screws (17) and then taking off the cover (16).
Pull the abrasive paper off the sanding/grinding
disk (6) and attach the new sheet of abrasive pa-
per (hook-and-loop fastening system).
6. Operation
6.1 ON/OFF switch (1)
To switch on the equipment set the On/Off switch
(1) to position I.
Move the ON/OFF switch (1) to position 0 to
switch off the equipment.
After switching on the equipment wait for the
equipment to reach its maximum speed of rotati-
on before commencing with the sanding/grinding
work.
6.2 Grinding/sanding
•
•
•
•
- 22 -
www.sidirika-nikolaidi.gr
(Figs. 14-16)
Warning! Before adjusting the grinding/san-
ding belt: Pull out the power plug!
The grinding/sanding belt should run centrally
on the rollers (see Fig. 14).
After changing the grinding/sanding belt (5),
turn the grinding/sanding belt (5) by hand
until the grinding/sanding belt has settled in a
certain position.
If necessary, you can use the adjustment
knob (32) to adjust the lateral displacement.
Important! While you are adjusting the lateral
displacement using the adjustment knob (32),
turn the grinding/sanding belt (5) by hand at
the same time or in between.
To move the grinding/sanding belt to the right,
turn the adjustment knob (32) clockwise (see
Fig. 15).
To move the grinding/sanding belt to the left,
turn the adjustment knob (32) counterclock-
wise (see Fig. 16).
ding/sanding disk (Fig. 6)
Always hold the workpiece firmly during grin-
ding/sanding.
Do not exert excessive pressure.
To prevent the abrasive paper from becoming
worn on one side, the workpiece should be
moved to and fro on the grinding/sanding belt
or grinding/sanding plate as you grind/sand.
Important! Pieces of wood should always