Hendi 222140 v.02 Benutzerhandbuch Seite 12

Whisk 222263 (optional) for 221884 v.02, 221891 v.02
GB
(Fig.6 on page 5)
Part
no.
1 Silicone rubber ring
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Circuit diagram
222140 v.02
(Fig.7 on page 6)
A. Variable resistor
B. Start
221884 v.02, 221891 v.02 , 222393 v.02
(Fig.8 on page 6)
A. Variable resistor
12
Part name
Spline
Ø8 Snap ring
Bearing washer
Bearing
Connect sleeve
Gear shaft
Screw plunger
Housing screw
Up seal ring
Upper cover
Needle bearing
Screw
Screw
Baffle plate
Ø16 Snap ring
Gear B
Cylindrical pin
Straight gear
Output axis
Key
Down seal ring
Lower cover
Oil sealing
set screw
Cylindrical pin
Fixed board
Steel ring
Steel bar
Fastening sleeve
Shaft sleeve
B. Start
C. Safety button
D. Lock
Quantity
Preparation before use
1
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
1
cessories. In case of incomplete or damaged delivery, please
4
contact the supplier immediately. In this case, do not use the
device.
2
• Clean the accessories and the appliance before use (See ==>
2
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
1
• Place the appliance on a horizontal, stable and heat resistant
1
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
1
the future.
4
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
1
a light odor during the first few uses. This is normal and does
1
not indicate any defect or hazard. Make sure the appliance is
2 well ventilated.
3
Preparations before bracket mounting on the
wall (222393 v.02 only)
1
Before installation: Check the wall bracket for any damage
1
& the completeness of the installation kits set of mounting
1
screws, washers and expansion bolts included). DO NOT install
if any missing or damage.
1
Note:
1
• Consult a qualified contractor or installer for assistance if you
are not certain about the structure of the wall and ensure that
2
the procedure is carried out properly and safely.
2
• Installation work should be done by qualified technicians for
the reason of safety.
2
• The distance between the holes of mounting screws is about
1
217mm. Make clear the surrounding before installation.
• Important: Before starting bracket mounting on the wall,
1
make sure you have all the tools, such as screw driver, elec-
2
tric drills, measuring tape, marking pencil (All are not includ-
2
ed).
• The bracket must be securely anchored on a wall by attaching
2
two mounting screws with the expansion bolts inserted.
2
• Be aware of the items such as ducts, electrical wires and wa-
ter pipes that hide behind the walls in your work area. Special
2
care is required during installation.
2
Operating instructions
1
222140 v.02
2
CAUTION: Before connecting the appliance to the power supply,
check that the power supply voltage corresponds with the pow-
er supply details shown on the rating label.
REMARK: There is no lock function for continuous operation for
this model 222140 v.02.
Operating the appliance
1. Ensure that the appliance is disconnected from the power
supply before assembly.
2. Connect the blending shaft/whisk to the main unit.
3. Check that the ON/OFF button is in the released (flat) po-