Kärcher HD 6/15 M Cage Bedienungsanleitung Seite 11

Safeý
devices
protect the чsеrапd
may not Ье
disabled
or
functionally circumvented.
The
очеrflоw
valve, pressure switch
ап
safety valve аrе
set апd
sealed
Ьу
the mапчfасfurеr. Adjustments аrе
performed опlу
Ьу
customer service.
overfiow
valve
w}th
рrеsSчrс
switch
Whеп
the
wаtеr quantity is reduced via the рrеssчrе/
quantity
сопtгоl оп the
trigger gчп, the overflow valve
орепs апd part of the water
floWS
back
to
the Suction
side
of
the рчmр.
Whеп
the
trigger
оп
the high-pressure gчп is release,
the pressure
Switch
switches ofi the high-pressure
рчmр and the high_pressure
jet StopS.
Тhе рчmр Switches оп again
Whеп the
trigger
iS
pul|ed
SaЪty
valve
The safeý
valve openS
When the
permissib|e operating
pressure
iS
exceeded and
the Water floWS
back to
the
suction side
of
the pump.
See
graphics page
О
Protector
@
Nozzle
@ Pressure апd quantity
фulаtiоп*
@ EASYlLockSpray|ance
@
ВЛSYtГоrсе high-pressure gчп
@
Satety
tatctr
@
Trigger
@
Uпlосkiпg lечег
Ф
EASYlLock
high-pressure hose
@ Push
handle
@
Spray
lапсе holder
@ Transport
rеtаiпег for surface
сlеапеr',
rotary поz-
zle"
@
Pustr handle stаr grip
_.
@
EASY!Lock
high-pressure соппесtiоп
@
Uпiоп
nut
@
Hosespout
@ Sieve
@ Water соппесtiоп
@
Power switch
@
СаЫе
clip, hose switch
*
not
iп
the
scope
of
delivery
for
a|l
unit
models
control
elements
fоr
the cleaning process are yel-
low
control elements
for
mаiпtепапсе
апd
ýervicing аrе
light grey.
Notifythe dealer immediately
iп
the
case
of
shipping
damage.
лrоfе
rhе ЕДsУ/Lосk
system соппесts соmропепts
quickly
апd safely
Via
а
single tum
of the
quiсk-rёlеаsе thrcad.
,1.
Plug the high-pressure nozzle
опtо
the Spray lапсе.
2.
Fit
the uпiоп
nut
and hand-tighten
(EASYlLock).
3.
Соппесt the spray lапсе
to
the high-pressure gun
апd hand-tighten
(EASY!Lock),
'FigureA
4.
Fit
the рцsh handle.
Figure
В
1
.
connect
the high-pressure hose
to
the high-pres-
Sчrе gun апd high-pressure соппесtiоп
of
the de-
чiсе and tighten hand-tight
(EASY!Lock).
^
DАNGЕR
Risk
of
iпiчry frоm
elecИc
shock
Use
а
plug
to
соппесt
the
device
to
the mаiпs
gid.
Реr-
mапепt соппесtiоп
to
the mаiпs
gid
is prohibited. The
p/ug
is used
for
dbconnection
from
the mаiпs,
See
the
type plate
оr
technical data
for
the соппесtiоп
valueS.
1.
Unwind the mаiпS
саЬ|е
апd place
оп the
ground.
2.
Plug the mаiпs plug
into
the socket.
:.
.
'.
':,.
-,,:,]],.:r]lil|atй]iкiiiiiмion
,]::.,:i-:::]::
:].,
connection
to
а
water line
А
WARN|NG
Health
/sk
from
rешrп flow of сопtаmiпаtеd water
into the
diпkiпg
water network,
obseмe
the
regulations
of
уоur
water
supply соmрапу.
According
to
applicable regulations, the device must
never
Ье
used
with the drinking Water network without
а
system Sераrаtоr.
Use
а
system Separator frоm
KARCHER
оr
а system Sераrаtоr as реr
EN
12729
Туре ВА. Water that has flowed thrочgh а System
sep-
аrаtоr is classified as.undrinkable.
Always
соппесt the
System Sераrаtоr
to
the Water
supply апd
печеr
directly
to the
water соппеёtiоп
оп
the device.
1.
check
the feed рrеSsчrе,
input
temperature апd in-
put
amount
of
the water sчррlу.
See the "Technical
data" section
for
the requiгements.
2.
connectthe
system Separator апd
waterconnection
of
the device with а hose (miпimчm length 7.5
m,.
minimum diameter
1").
The supply hose
iS not
included
in
the
scope
of
de-
livery,
3.
Ореп
the
water
inlet.
suck
water from
the
container
1.
SсrеW the Suction
hose
(оrdег number
4.440-207.0)
and filter (оrdеr пчmЬеr4.730-012,0) опtо the Water
connection.
2.
ventthe
device.
vent
the
device
1
.
Unscrew the nozzle
frоm
the sрrау lапсе.
2.
Allow the device
to гчп until
the escaping
Water
iS
free
of
аir bubbles.
3.
lп
the case
of
venting рrоЬlеms, allow the device to
ruп
fоr
1
0
seconds
and then Switch
it
ofi,
Repeat the
procedure Several times.
switch
off
the device.
Screw the nozzle back
in
place
о
a
4
5
10
English